Yamaha YP125R Скачать руководство пользователя страница 212

Страница: 212 / 498

REAR BRAKE

4-37

EAS22560

INTRODUCTION

WARNING

EWA14101

Disc brake components rarely require disas-
sembly. Therefore, always follow these pre-
ventive measures:
• Never disassemble brake components un-

less absolutely necessary.

• If any connection on the hydraulic brake

system is disconnected, the entire brake
system must be disassembled, drained,
cleaned, properly filled, and bled after reas-
sembly.

• Never use solvents on internal brake com-

ponents.

• Use only clean or new brake fluid for clean-

ing brake components.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.

• Avoid brake fluid coming into contact with

the eyes as it can cause serious injury.

FIRST AID FOR BRAKE FLUID ENTERING
THE EYES:
• Flush with water for 15 minutes and get im-

mediate medical attention.

EAS22570

CHECKING THE REAR BRAKE DISC

1. Remove:

• Rear wheel

Refer to “REAR WHEEL” on page 4-15.

2. Check:

• Brake disc

Damage/galling

→

Replace.

3. Measure:

• Brake disc deflection

Out of specification

→

Correct the brake disc

deflection or replace the brake disc.
Refer to “CHECKING THE FRONT BRAKE
DISC” on page 4-22.

4. Measure:

• Brake disc thickness

Measure the brake disc thickness at a few dif-
ferent locations.
Out of specification

→

Replace.

Refer to “CHECKING THE FRONT BRAKE
DISC” on page 4-22.

5. Adjust:

• Brake disc deflection

Refer to “CHECKING THE FRONT BRAKE
DISC” on page 4-22.

6. Install:

• Rear wheel

Refer to “REAR WHEEL” on page 4-15.

EAS37P1131

REPLACING THE REAR BRAKE PADS
(YP125R)

TIP

When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disassem-
ble the brake caliper.

1. Measure:

• Brake pad wear limit “a”

Out of specification

→

Replace the brake

pads as a set.

2. Install:

• Brake pad spring

• Brake pads

Brake disc deflection limit

0.25 mm (0.0098 in) (YP125R)
0.15 mm (0.0059 in) (YP250R)

Brake disc thickness limit

4.5 mm (0.18 in)

Rear brake disc bolt

23 Nm (2.3 m·kgf, 17 ft·lbf)
LOCTITE®

Brake pad lining thickness (in-
ner)

7.3 mm (0.29 in)

Limit

0.8 mm (0.03 in)

Brake pad lining thickness (out-
er)

7.3 mm (0.29 in)

Limit

0.8 mm (0.03 in)

New

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды