background image

17

Please observe the following instructions for proper handling of the gas spring.

PRECAUTIONS FOR HANDLING GAS SPRING

2. Instructions for discarding the gas spring

Make sure to observe the following instructions when discarding the gas spring.
As pressurized nitrogen gas is sealed in the gas spring, be sure to release before discarding it. Or an explo-
sion may occur, causing an injury.

[PRECAUTIONS]

A.  Do not crash.
B.  Do not cut.
C.  Do not make a hole anywhere other than the speci-

fied positions (

q

 

and 

w

 in the Fig.1).

D.  Do not throw it in the fire.

[Discarding procedure]

1.  Put the gas spring in a plastic bag. Using a drill of 2 to 3 mm, 

make  a  hole 

q

  from  outside  of  the  plastic  bag  at  the  posi-

tion as specified in the figure to release the gas and oil and 
then make a hole 

w

 at the position as specified. 

(Be sure to 

make holes in the order of 

q

 

and 

w

. )

2.  If a vinyl bag is not used, the oil and drill chips will spread. (In 

such a case, wear eye protection glasses. )

* Drill 2 holes as shown above to release 

the gas before discarding the gas spring.

  Do not apply a high tensile load to the gas spring as it will cause damage to the gas spring.

 In the event of a failure, stop using the instrument and contact the shop of its purchase. If your dealer 

is unable to assist you, please contact Yamaha directly.

This  gas  spring  requires  no  oil  supply  to  its  sliding 

section. Additional oil will reduce the sealing durabil-

ity and cause the oil to leak.

Never  apply  any  impact  to  the  gas  spring.  It  will 

cause oil leakage, malfunction or breakage.

Never  disassemble  the  gas  spring.  As  a  high  pres-

sure gas is sealed in it, disassembling it will cause a 

high risk.

Note that there is not much rigidity in the bending di-

rection. Depending on accuracy in its installation, the 

bending load will cause the rod to bend, resulting in 

malfunction.

1. Precautions for handling the gas spring

q

w

35mm

15mm

Drill 

Plastic bag

Fig. 1 

 Caution

Injury or handicaps to persons caused by the disregard of warnings with 

this mark or, misuse of the instrument, may result in the loss of personal 

property.

Please change cracked tone bars as soon as possible. Cracked tone bars have sharp edges that can cut hands.

If the instrument is often moved, bolts, parts, etc., may become loose. After moving the instrument, check and make 

sure all bolts, parts, etc., are firmly fastened. Firmly tighten all loose items.

Do not use the hammer for anything other than playing the instrument. It may be the cause of injury or accidents. Do 

not let children strike other, etc., with the mallet. Do not allow such dangerous behavior to take place.

When assembling, be careful not to pinch your fingers or hands. Take special care when assembling rails and reso-

nator pipes. Two persons should carry out this part of the assembly, double-checking as the assembly proceeds.

 Caution

 Danger

Note  that  a  nick  on  the  piston  rod  or  cylinder  will 

shorten  the  service  life  of  the  sealing  or  cause  a 

malfunction.

Do  not  expose  the  gas  spring  to  an  excessively 

high or low temperature. The allowable temperature 

range for use is -20°C to 80°C.

Avoid using the instrument where it is exposed to to 

rain, water or much dust.

Do not apply an excessive force to lift the frame end 

and pull off the gas spring from the leg.

02_ym5100_en.indd   17

14/10/10   10:17

Содержание YM-4600A

















Отзывы: