Yamaha YFM700RSBH Скачать руководство пользователя | Manualshive

Страница: 120 / 160

background image

8-28

8

3. Check the engine idling speed and, if neces-

sary, adjust it to specification by turning the
idle adjusting screw. To increase the engine
idling speed, turn the idle adjusting screw in
direction (a), and to decrease it, turn the
screw in direction (b).

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24048

Adjusting the throttle lever free play

The throttle lever free play should be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
The throttle lever free play should measure 2.0–4.0
mm (0.08–0.16 in) as shown. Periodically check
the throttle lever free play and, if necessary, adjust
it as follows.

TIP

The engine idling speed must be checked, and
adjusted if necessary, before adjusting the throttle
lever free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle lever free play, turn

the throttle lever free play adjusting bolt in di-
rection (a). To decrease the throttle lever free
play, turn the adjusting bolt in direction (b).

1. Idle adjusting screw

Engine idling speed:

1500–1700 r/min

1

(a)

(b)

U2LS62E0.book Page 28 Thursday, February 25, 2016 8:44 AM

«
...
118
119
120
121
122
...
»

Содержание YFM700RSBH

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM700RSBH

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды