Yamaha YFM700RSBH Скачать руководство пользователя | Manualshive

Страница: 113 / 160

background image

8-21

8

9. Connect the coolant reservoir hose.

10. Pour the recommended coolant into the res-

ervoir to the maximum level mark, and then
install the reservoir cap.

NOTICE:

Mix anti-

freeze with distilled water only. However, if
distilled water is not available, soft water
may be used for refilling. Do not use hard
water or salt water since they are harmful
to the engine.

[ECB00992]

11. Pour the recommended coolant into the radi-

ator until it is full.

12. Install the radiator cap, start the engine, let it

idle for several minutes, and then turn it off.

13. Remove the radiator cap to check the coolant

level in the radiator. If it is low, add sufficient
coolant until it reaches the top of the radiator,
and then install the radiator cap.

14. Start the engine, and then check for coolant

leakage.

TIP

If any leakage is found, have a Yamaha dealer
check the cooling system.

15. Install the panel.

EBU26808

Cleaning the air filter element

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are rid-
ing in unusually wet or dusty areas.

TIP

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.

Antifreeze/water mixture ratio:

1:1

Recommended antifreeze:

High-quality ethylene glycol antifreeze con-
taining corrosion inhibitors for aluminum
engines

Coolant quantity:

Radiator (including all routes):

1.68 L (1.78 US qt, 1.48 Imp.qt)

Coolant reservoir (up to the maximum level
mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

U2LS62E0.book Page 21 Thursday, February 25, 2016 8:44 AM

«
...
111
112
113
114
115
...
»

Содержание YFM700RSBH

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM700RSBH

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды