Yamaha YFM450FAZ Скачать руководство пользователя | Manualshive

Страница: 125 / 166

background image

8-37

8

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

5. Install the panel.

EBU24045

Adjusting the throttle cable free play

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U37S61E0.book Page 37 Tuesday, June 2, 2009 10:33 AM

«
...
123
124
125
126
127
...
»

Содержание YFM450FAZ







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM450FAZ

Бренд: Yamaha Страницы: 32

Бренд: Ohlins Страницы: 8

Бренд: Sym Страницы: 31

Two Fifty 250 cc

Бренд: Mash Страницы: 62

fire PANTLINER AJ6

Бренд: ALPENHEAT Страницы: 26

Бренд: Crivit Страницы: 30

Krauser 630.2516

Бренд: hepco & becker Страницы: 6

Бренд: Honda Страницы: 224

H-AFT18-15-01-SL

Бренд: SRC Страницы: 3

B-TRK502-01-01-SL

Бренд: SRC Страницы: 5

Бренд: DYNATEK Страницы: 5

Бренд: tucanourbano Страницы: 4

Sport 1 180 - 487.3

Бренд: CZ Страницы: 42

Siegen Tools S01001.V3

Бренд: Sealey Страницы: 4

Бренд: Kemimoto Страницы: 3

Бренд: KTM Страницы: 2

Бренд: Honda Страницы: 168

Бренд: Honda Страницы: 305

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды