background image

Components 

The XW-CS-700 kit includes the following components.  Please check that you received all of them: 

Revolabs

 HD dual

:

  The HD dual includes the Receiver for the wireless microphone, the Charger to charge up 

to two microphones, and the required power adapters. 

Revolabs HD

 omni-directional wireless microphone.

 

Proprietary audio cable to connect the HD dual Receiver to the CS-700. 

User guide (this document). 

 

Preparing the wireless Receiver 

Before enabling the wireless extension microphone with the CS-700, the wireless Receiver needs to be configured and a 
connection between the wireless extension microphone and the Receiver needs to be created. 

Charging the microphones 

First,  please  charge  the microphone  battery  for at  least  an hour to ensure that enough charge  is in the  battery to go 
through the process.  To charge, connect the Charger to the main powers using one of the provided 5VDC AC Adapters 
and using an appropriate power outlet 110-240 AC, 50-60Hz. The power LED on the Charger will illuminate.  Place the 
microphone in the Charger and ensure that it is seated well in the charging bay.  Either a solid red LED (charging) or solid 
green LED (100% charged) light will appear to confirm that the microphone is inserted properly. While in the Charger, the 
microphones are not transmitting audio to the Receiver. In normal use, batteries should fully charge in about 2 hours, but 

will “quick

-

charge” to 80% capacity in approximately 1 hour and 20 minutes. Fully charged mic

rophones left in the Charger 

remain solid green.  Before first use of the microphone it should be charged for several hours or until the LED on the 
microphone turns green in the Charger.   

Whenever microphones are not in use, they should be inserted into the Charger. It is important to ensure that all 
microphones are inserted fully so that charging will occur. Features of the Charger are shown in the following image. 

 

 

 

 

 

 

 

 

1. LED indicator 

 power status indicator   

 

2. Charger Bays 

 charges up to 2 Microphones 

 

3. Power Cord Receptacle 

 power supply input, 5 VDC (on rear) 

 

Important

The Serial Number of the Microphones used with the XW-CS-700 should start with a 7010 or 8020.  

Serial numbers starting with numbers different than 7010 or 8020 are not approved to be used with the CS-700 
extension microphone kit!  In the supported microphones the Lithium Polymer rechargeable batteries that 
power the microphones are field replaceable.  Replace the batteries only with the manufacturer and model 
battery type recommended by Yamaha Unified Communications.  Please contact Yamaha Unified 
Communications (uc.yamaha.com) for correct manufacturer approved and recommended replacement type 
batteries. 

Caution

: Risk of explosion if batteries are mishandled or replaced by an incorrect type.  Do not disassemble 

batteries or attempt to charge outside the system.   Do not dispose of batteries in fire.   Dispose of batteries in 
accordance with manufacturer’s instructions and local regulations.  

 

Содержание XW-CS-700











Отзывы: