background image

CONSUMER INFORMATION

9-7

9

EAU26663

YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED 
WARRANTY 

a)
b)

c)

d)
e)

f)

1.

2.

Yamaha Motor Corporation, U.S.A. hereby warrants that 
new Yamaha motorcycles will be free from defects in 
material and workmanship for the period of time stated 
herein, subject to certain stated limitations.

THE PERIOD OF WARRANTY

 for Yamaha motorcycles 

originally equipped with headlight, stoplight, and turn 
signals shall be one (1) year from the date of purchase, 
with no mileage limitation.

MODELS EXCLUDED FROM WARRANTY

 include 

those used for non-Yamaha-authorized renting, leasing 
or other commercial purposes, and TZ models.

DURING THE PERIOD OF WARRANTY,

 any authorized 

Yamaha motorcycle dealer will, free of charge, repair or 
replace any part adjudged defective by Yamaha due to 
faulty workmanship or material from the factory. Parts used 
in warranty repairs will be warranted for the balance of the 
product’s warranty period. All parts replaced under 
warranty become property of Yamaha Motor Corporation, 
U.S.A.

GENERAL EXCLUSIONS

 from this warranty shall 

include any failures caused by:

Competition or racing use.
Installation of parts or accessories that are not 
qualitatively equivalent to genuine Yamaha parts.
Abnormal strain, neglect, or abuse.
Lack of proper maintenance.
Accident or collision damage.
Modification to original parts.

SPECIFIC EXCLUSIONS

 from this warranty shall 

include parts replaced due to normal wear or routine 
maintenance.

THE CUSTOMER’S RESPONSIBILITY

 under this 

warranty shall be to:

Operate and maintain the motorcycle as specified in 
the appropriate Owner’s Manual, and
Give notice to an authorized Yamaha motorcycle 
dealer of any and all apparent defects within ten (10) 
days after discovery, and make the machine available 
at that time for inspection and repairs at such dealer’s 
place of business.

WARRANTY TRANSFER:

 To transfer the warranty from 

the original purchaser to any subsequent purchaser, it is 
imperative that the machine be inspected and registered 
for warranty by an authorized Yamaha motorcycle dealer. 
In order for this warranty to remain in effect, this 
inspection and registration must take place within ten 
(10) days after transfer. An inspection and registration fee 
will be charged for this service.

EMISSION CONTROL SYSTEM WARRANTY:

Yamaha Motor Corporation, U.S.A. also warrants to the 
ultimate purchaser and each subsequent purchaser of 
each Yamaha motorcycle covered by this warranty with a 
displacement of 50cc or greater, that the vehicle is 
designed, built, and equipped so as to conform at the 
time of sale with all U.S. emissions standards applicable 
at the time of manufacture and that it is free from defects 
in materials and workmanship which would cause it not 
to meet these standards within the period listed 
immediately below. Failures other than those resulting 
from defects in material or workmanship, which arise 
solely as a result of owner abuse and/or lack of proper 
maintenance, are not covered by this warranty.

Period

6,000 km (3,750 miles)

or five years, whichever occurs first

12,000 km (7,465 miles)

or five years whichever occurs first

18,000 km (11,185 miles)

or five years, whichever occurs first

30,000 km (18,641 miles)

or five years, whichever occurs first

YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO 
OTHER WARRANTY OF ANY KIND, EXPRESSED OR 
IMPLIED. ALL IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE WHICH EXCEED THE 
OBLIGATIONS AND TIME LIMITS STATED IN THIS 
WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA 
MOTOR CORPORATION, U.S.A. AND EXCLUDED 
FROM THIS WARRANTY.

SOME STATES DO NOT ALLOW LIMITATIONS ON 
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE 
ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO 
EXCLUDED FROM THIS WARRANTY ARE ANY 
INCIDENTAL OR CONSEQUENTIAL DAMAGES 
INCLUDING LOSS OF USE. SOME STATES DO NOT 
ALLOW THE EXCLUSION OR LIMITATION OF 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO 
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL 
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS 
WHICH VARY FROM STATE TO STATE. 

YAMAHA MOTOR CORPORATION, U.S.A.

P.O. Box 6555

Cypress, California 90630

Engine 
Displacement

 

Under 50cc

50cc to 169cc 

170cc to 279cc 

280cc and over

U3D810E0.book  Page 7  Wednesday, July 19, 2006  11:14 AM

Содержание XVS13AW


































































































Отзывы: