Yamaha XVS13AW Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 97

background image

MOTORCYCLE CARE AND STORAGE

7-4

7

3. Perform the following steps to pro-

tect the cylinders, piston rings, etc.
from corrosion.

a. Remove the spark plug caps

and spark plugs.

b. Pour a teaspoonful of engine oil

into each spark plug bore.

c. Install the spark plug caps onto

the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)

d. Turn the engine over several

times with the starter. (This will
coat the cylinder walls with oil.)

e. Remove the spark plug caps

from the spark plugs, and then
install the spark plugs and the
spark plug caps.

WARNING

EWA10950

To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.

4. Lubricate all control cables and the

pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.

5. Check and, if necessary, correct

the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.

6. Cover the muffler outlet with a

plastic bag to prevent moisture
from entering it.

7. Remove the battery and fully

charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30°F) or more than 30
°C (90°F)]. For more information
on storing the battery, see page
6-29.

NOTE:

Make any necessary repairs before
storing the motorcycle.

U3D810E0.book Page 4 Wednesday, July 19, 2006 11:14 AM

«
...
79
80
81
82
83
...
»

Содержание XVS13AW


































































































Отзывы:

Нет отзывов

Похожие инструкции для XVS13AW

WARRIOR YFM350XS

Бренд: Yamaha Страницы: 46

Бренд: Yamaha Страницы: 88

Бренд: hepco & becker Страницы: 6

Бренд: Honda Страницы: 60

Бренд: RDMOTO Страницы: 2

990D0-31J50-CLE

Бренд: Suzuki Страницы: 12

Бренд: Thunderbike Страницы: 7

RMAX WOLVERINE 2021

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 396

Бренд: Yamaha Страницы: 192

Бренд: Shad Страницы: 12

Бренд: MSW Страницы: 11

Бренд: Shad Страницы: 2

Rumbler 500 2017

Бренд: Royal Enfield Страницы: 160

Бренд: BOS Suspension Страницы: 32

XSM POWER UP 2007

Бренд: Malaguti Страницы: 53

Бренд: Kinroad Страницы: 25

Бренд: ZTechnik Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды