Yamaha XT250D страница 72 Скачать руководство пользователя

Страница: 72 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-34

bulb cover.

4. Remove the headlight bulb holder

by turning it counterclockwise, and
then remove the burnt-out bulb.

5. Place a new bulb into position, and

then secure it with the bulb holder.

6. Install the bulb cover, and then

connect the coupler.

7. Place the headlight unit in the orig-

inal position, and then install the
bolts.

8. Install the cowling.
9. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24133

Replacing the tail/brake light
bulb

1. Remove the tail/brake light lens by

removing the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

1. Headlight coupler

2. Headlight bulb cover

1. Headlight bulb holder

1. Tail/brake light lens

2. Screw

1YB-9-10.book 34 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды