Yamaha XL700 WaveRunner 2003 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 117

Yamaha XL700 WaveRunner 2003 Скачать руководство пользователя страница 94

4-15

E

NOTE:

@

●

Wipe off any water on the spark plug or
inside the cap before installing the spark
plug cap. Push the spark plug cap down
until it clicks.

●

If a torque wrench is not available when
you are fitting a new spark plug, a good
estimate of the correct torque is 1/4 turn
to 1/2 turn past finger tight. Have the
spark plug adjusted to the correct torque
with a torque wrench as soon as possible.

@

WARNING

@

Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks
to escape, which could lead to explosion
or fire.

@

EJU01139

Lubrication points

To keep moving parts sliding or rotating

smoothly, coat them with water-resistant
grease.

Recommended water-resistant grease:

Yamaha Marine Grease/
Yamaha Grease A

●

Throttle cable (carburetor end)

●

Choke cable (carburetor end)

UF0M14.book Page 15 Wednesday, July 31, 2002 2:30 PM

«
...
92
93
94
95
96
...
»

Содержание XL700 WaveRunner 2003






















































































































Отзывы:

Нет отзывов