Yamaha XL700 WaveRunner 2003 Скачать руководство пользователя страница 29

Страница: 29 / 117

2-2

Engine shut-off cord (lanyard)

Attach to wrist so that the engine stops if the
operator falls off the watercraft.

Engine stop switch

Push to stop the engine normally.

Clip

Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent acci-
dental starting of the engine or unauthorized
use of the watercraft.

Engine shut-off switch

Remove the clip to stop the engine and dis-
able it from starting.

Start switch

Push to start the engine.

Oil level warning lamp

Throttle lever

Use to accelerate and decelerate.

Stern drain plugs

Use to drain water in the bilge when the water-
craft is on dry land.

Jet thrust nozzle

Changes the direction of jet thrust according
to handlebar position.

Cleat

Use to attach a towrope for pulling water-skier
or a rope mooring the watercraft.

Ride plate

UF0M14.book Page 2 Wednesday, July 31, 2002 2:30 PM

Содержание XL700 WaveRunner 2003






















































































































Результаты поиска

Содержание XL700 WaveRunner 2003

Отзывы:

Yamaha XL700 WaveRunner 2003, Руководство владельца/оператора, Страница: 29 / 117

Результаты поиска

Содержание XL700 WaveRunner 2003

Отзывы: