Yamaha XL700 WaveRunner 2001 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 120

background image

2-15

E

EJU01236

Storage compartments

A front storage compartment, a glove

compartment, and seat storage compart-
ments are provided.

NOTE:

@

●

Make sure that the storage compartments
are properly secured before operating the
watercraft.

●

The storage compartments are not
designed to be waterproof. If you carry
objects that must be kept dry, such as the
manuals, put them in a waterproof bag.

@

EJU01133

Front storage compartment

Two storage compartments are located at

the bow.

To open the front storage compartment,

pull the hood latch

1

up, and then open the

hood.

To close the front storage compartment,

push down on the rear of the hood until it
latches securely.

NOTE:

@

The lower storage compartment

3

is pro-

vided under the upper storage compart-
ment

2

.

To access the lower storage compartment,
remove the upper storage compartment.

@

CAUTION:

@

Store only soft, light weight objects,
such as rope or rags, in the lower storage
compartment. Storing hard or heavy
objects, such as tools or cans, may dam-
age the compartment.

@

Upper storage compartment:

Capacity: 44 L (4.4 US gal, 3.6 Imp gal)
Load limit: 5 kg (11 lb)

UF0M15.book Page 15 Tuesday, June 3, 2003 3:36 PM

«
...
40
41
42
43
44
...
»

Содержание XL700 WaveRunner 2001

























































































































Отзывы:

Нет отзывов

Похожие инструкции для XL700 WaveRunner 2001

Бренд: COBIA Страницы: 24

Бренд: Cal Boats Страницы: 38

45 COCKPIT MOTOR

Бренд: Carver Страницы: 141

Бренд: Yamarin Cross Страницы: 116

Бренд: Scout Boats Страницы: 109

Бренд: Grand Soleil Страницы: 103

Бренд: Grady-White Boats Страницы: 72

Бренд: Whittaker Страницы: 72

Бренд: TAKACAT Страницы: 14

Бренд: PATHFINDER Страницы: 28

MK II FORMOZA 550 SOF COMBAT

Бренд: Wayland Folding Kayaks Страницы: 9

XL700 WaveRunner 2001

Бренд: Yamaha Страницы: 118

Бренд: Grady-White Boats Страницы: 111

Бренд: BRIG Страницы: 36

Бренд: BRIG Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды