Yamaha XL700 WaveRunner 2001 Скачать руководство пользователя | Manualshive

Страница: 38 / 120

background image

2-11

E

EJU01130

Cooling water pilot outlet

This watercraft is equipped with a cooling

water pilot outlet.

When the engine is running, cooling

water is circulated in the engine, and then it
is discharged from the pilot outlet.

To check for proper operation of the cool-

ing system, check that water is being dis-
charged from the pilot outlet. If water is not
being discharged from the outlet, cooling
water may not be circulating in the engine.
When this occurs, stop the engine and
check for the cause. (See pages 2-13 and
5-3 for further instructions.)

NOTE:

@

If the cooling water passages are dry, it will
take about 20 seconds for the water to reach
the outlet after the engine is started.

@

EJU01021

Steering system

Your watercraft can be steered by turning

the handlebars

1

the same direction you

wish to travel.

When the handlebars are turned, the

angle of the jet thrust nozzle

2

is changed,

and the direction of the watercraft is
changed accordingly. Since the strength of
the jet thrust determines the speed and
direction of a turn, the throttle must always
be open when attempting a turn, except at
trolling speed.

UF0M15.book Page 11 Tuesday, June 3, 2003 3:36 PM

«
...
36
37
38
39
40
...
»

Содержание XL700 WaveRunner 2001

























































































































Отзывы:

Нет отзывов

Похожие инструкции для XL700 WaveRunner 2001

2014 32 Corsair RK

Бренд: Chris-Craft Страницы: 234

Бренд: Sea-doo Страницы: 130

Бренд: Sea-doo Страницы: 138

Бренд: Sea-doo Страницы: 144

Бренд: Mercury Страницы: 88

Бренд: PDQ Yachts Страницы: 66

GP1200R WaveRunner 2001

Бренд: Yamaha Страницы: 245

Бренд: World Cat Страницы: 74

Бренд: World Cat Страницы: 91

Бренд: World Cat Страницы: 98

Бренд: 3D Tender Страницы: 18

Бренд: Lagoon Страницы: 39

LEADER 33 OUTBOARD

Бренд: Jeanneau Страницы: 198

MERRY FISHER 605

Бренд: Jeanneau Страницы: 96

2010 Ranger Tug R-29

Бренд: Rangertugs Страницы: 21

Waverunner VXS VX1800

Бренд: Yamaha Страницы: 318

Бренд: Arey's Pond Страницы: 10

Бренд: Barnett Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды