Yamaha XJ6N Скачать руководство пользователя страница 89

Страница: 89 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

6-44

TIP

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain does not need to
be disassembled in order to re-
move and install the rear wheel.

6. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

TIP

A rubber mallet may be useful to tap the
wheel axle out.

7. Remove the wheel.

NOTICE:

not apply the brake after the
wheel has been removed to-
gether with the brake disc, oth-
erwise the brake pads will be
forced shut.

[ECA11071]

EAU34434

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the right-hand side.

TIP

●

Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

2. Install the drive chain onto the rear

sprocket.

3. Install the axle nut.
4. Lower the rear wheel so that it is

on the ground, and then put the
sidestand down.

5. Adjust the drive chain slack. (See

page 6-27.)

6. Tighten the axle nut, and then

tighten the locknuts to the speci-
fied torques.

1. Brake caliper

2. Wheel axle

1. Brake caliper bracket
2. Slot

3. Retainer

Tightening torques:

Axle nut:

90 Nm (9.0 m·kgf, 65 ft·lbf)

Locknut:

16 Nm (1.6 m·kgf, 12 ft·lbf)

U20SE3E0.book Page 44 Monday, April 23, 2012 10:47 AM

Содержание XJ6N









































































































Результаты поиска

Содержание XJ6N

Отзывы:

Похожие инструкции для XJ6N

Бренды по названию

Популярные бренды

Yamaha XJ6N, Руководство пользователя

Результаты поиска

Содержание XJ6N

Отзывы:

Похожие инструкции для XJ6N

Бренды по названию

Популярные бренды