Yamaha WR250F 2022 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 404

background image

ENGINE

3-14

•

Seat

•

Side cover (left/right)
Refer to “GENERAL CHASSIS” on page 4-1.

EAM30224

CHECKING THE ENGINE OIL LEVEL

1. Stand the vehicle upright on a level surface.
2. Start the engine, warm this up for 2–3 min-

utes, and then stop the engine and wait about
1 minute.

3. Check:

•

Oil level
The engine oil level should be between the
minimum level mark “a” and maximum level
mark “b”.
Below the minimum level mark



Add the

recommended engine oil to the proper level.

NOTICE

ECA24290

• Since engine oil also lubricates the clutch,

the wrong oil types or additives could

cause clutch slippage. Therefore, do not

add any chemical additives.

• Do not allow foreign material to enter the

crankcase.

EAM30225

CHANGING THE ENGINE OIL

Stand the vehicle upright on a level surface.
1. Start the engine, warm this up for several

minutes, and then stop the engine and wait
about 5 minutes.

TIP

This model is equipped with an engine auto-stop
system. The engine stops automatically if left
idling for 7 minutes. If the engine stops, push the
start switch to restart the engine.

2. Place an oil pan under the drain bolt.
3. Remove:

•

Engine guard “1”

•

Oil filler cap “2”

•

Drain bolt (with gasket) “3”

4. If the oil filter element is also to be replaced,

perform the following procedure.
a. Remove the oil filter element cover “1” and

oil filter element “2”.

b. Replace the new O-ring “3”.

Recommended brand

YAMALUBE

SAE viscosity grades

10W-40, 10W-50, 15W-40, 20W-

40 or 20W-50

Recommended engine oil grade

API service SG type or higher,

JASO standard MA

a

b

2

1

3

«
...
100
101
102
103
104
...
»

Содержание WR250F 2022





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250F 2022

Бренд: Dakota Digital Страницы: 38

Бренд: Uclear Страницы: 2

Бренд: BMW Страницы: 245

Бренд: Graphite Страницы: 44

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

Бренд: R&G Страницы: 6

Бренд: hepco & becker Страницы: 6

Splendor Pro CLASSIC

Бренд: HERO Страницы: 56

Бренд: paladin Страницы: 2

Бренд: Sinnis motorcycles Страницы: 68

Бренд: KC Страницы: 32

Бренд: Suzuki Страницы: 101

Бренд: Custom Dynamics Страницы: 2

Бренд: Royal Enfield Страницы: 234

Бренд: SCHUBERTH Страницы: 43

Бренд: Twiins Страницы: 40

Бренд: Hama Страницы: 22

Бренд: Yamaha Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды