Generator cover
5-62
TIP:
Pass the pickup coil lead “a” between the gen-
erator cover and the bolt hole “b”, and then se-
cure the lead by installing the washer “4”.
Flywheel magneto assembly
1.
Install the starter clutch “1” to a new fly-
wheel magneto “2”.
2.
Hold the flywheel magneto “1” using the
special service tool “2”, and then tighten
new flywheel magneto bolts “3” to the
specified torque.
3.
Install the flywheel magneto “1” to the
starter gear “2”.
TIP:
Turn the starter gear “2” clockwise while install-
ing it onto the flywheel magneto “1”.
Flywheel magneto installation
Do not reuse a flywheel magneto, special
nut, flywheel magneto bolt, transfer shaft,
or Woodruff key, always replace it with a
new one.
1.
Remove any grease from a new special
nut “1” and the inner surface of a new
transfer shaft “2”, and then install the spe-
cial nut “1” into the transfer shaft “2” until it
can no longer be turned.
Holder bolt “5”
15 Nm (1.5 kgf·m, 11.1 ft·lb)
Stator coil bolt “6”
15 Nm (1.5 kgf·m, 11.1 ft·lb)
6
4
2
5
1
3
a
b
3
6
1
2
Sheave holder “2”
90890-01701
Primary sheave holder “2”
YS-01880-A
Flywheel magneto bolt “3”
24 Nm (2.4 kgf·m, 17.7 ft·lb)
2
1
3
3
3
1
2
Содержание WaveRunner VXR VX1800A
