manualshive.com logo in svg

Yamaha WaveRunner GP800R, Руководство по обслуживанию

Поделиться
Скачать
Yamaha WaveRunner GP800R Скачать руководство пользователя страница 34

3-3

INSP

ADJ

E

CONTROL SYSTEM

NOTE:

If the steering cable cannot be properly
adjusted at the steering column side, make
sure the steering cable at the jet pump side
is set to the specified length. Refer to
“REMOTE CONTROL CABLES AND SPEED
SENSOR LEAD” in chapter 8.

Throttle cable inspection and adjustment

NOTE:

Before adjusting the throttle lever free play,
adjust the trolling speed.

1. Measure:

●

Throttle lever free play 

a

 

Out of specification 

→

 Adjust.

2. Adjust:

●

Throttle lever free play

WARNING

The cable joint must be screwed in more
than 8 mm (0.31 in).

●

Connect the cable joint and tighten the
locknut.

T

 

R

.

.

Locknut:

6 N • m (0.6 kgf • m, 4.3 ft • lb)

Throttle lever free play:

4–7 mm (0.16–0.28 in)

Adjustment steps:

●

Loosen the locknut 

1

.

●

Turn the adjuster 

2

 in or out until the

specified free play is obtained.

Turn in 

Free play is increased.

Turn out 

Free play is decreased.

●

Tighten the locknut.

Содержание WaveRunner GP800R
























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды