manualshive.com logo in svg

Yamaha WaveRunner GP800R, Руководство по обслуживанию

Поделиться
Скачать
Yamaha WaveRunner GP800R Скачать руководство пользователя страница 146

6-19

E

JET

PUMP

BEARING HOUSING

SERVICE POINTS

Driven coupling removal and installation

1. Remove and install:

●

Driven coupling 

NOTE:

Install the driven coupling with the same
special tools that were used for removal.

Intermediate drive shaft removal

1. Remove:

●

Intermediate drive shaft

NOTE:

Support the intermediate housing with
steel blocks 

1

 and press the driven cou-

pling shaft.

Bearing removal

1. Remove:

●

Bearing 

NOTE:

●

Install the bearing with the same special
tools that were used for removal.

●

Support the intermediate housing with
steel blocks 

1

 and press the bearing.

Coupler wrench:

YW-06551/90890-06551

Shaft holder:

YB-06552/90890-06552

Removal steps:

●

Temporarily install the driven coupling
to the intermediate drive shaft.

●

Insert the long rod to the driven cou-
pling shaft.

●

Press out the intermediate drive shaft
by pushing the rod.

Driver rod:

YB-06071/90890-06606

Bearing outer race attachment:

YB-06016/90890-06626

1

Содержание WaveRunner GP800R
























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды