background image

E

2-17

EMU00147

Fuel Flow Meter

The  meter  displays  fuel  flow  within  one
hour, at the rate of current engine operation.

If  twin  engines  are  installed  on  your  boat,
the  meter  will  display  total  fuel  flow  of  Port
and  Starboard  side  engine. It  also  displays
PS indication at the same time.
By  pressing “set” button,  the  meter  will  dis-
play  fuel  flow  of  starboard  side  engine  and
S indication.
By  pressing  “set” button  again,  the  meter
will display fuel flow of port side engine and
P indication.
By  pressing  “set” button  again,  the  meter
will display total fuel flow.

NOTE:

8

The  meter  displays  gallon/hour  and  liter
depending  upon  operator  preference.
Select  the  desired  unit  of  measurement
by  setting  the  selector  switch 

1

on  the

back of the meter during installation.

8

Fuel consumption meter and Fuel econo-
my  meter  will  indicate  same  unit  of  mea-
surement.

YAMAHA

P S

gph

I/h

ECON SYNC

TTL

FUEL MANAGEMENT

set

mode

000335

2

6

5

4

3

1

ON

(liter)

l/h

(gallon)

gph

q

000336

 60V-9-11-2  7/31/02 10:26 AM  Page 18

Содержание VZ225B































































































































Отзывы: