Yamaha VZ200D Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 80

background image

Operation

34

EMU27820

Stopping engine

Before stopping the engine, first let it cool off
for a few minutes at idle or low speed. Stop-
ping the engine immediately after operating
at high speed is not recommended.

EMU27851

Procedure

1.

Turn the main switch to “

” (off).

2.

After stopping the engine, disconnect
the fuel line or close the fuel cock if there
is a fuel joint or a fuel cock on the boat.

3.

Tighten the air vent screw on the fuel
tank cap (if equipped).

4.

Remove the key if the boat will be left
unattended.

NOTE:

The engine can also be stopped by pulling
the lanyard and removing the clip from the
engine stop switch, then turning the main

switch to “

” (off).

EMU27861

Trimming outboard motor

The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. Correct trim angle will help im-
prove performance and fuel economy while
reducing strain on the engine. Correct trim
angle depends upon the combination of
boat, engine, and propeller. Correct trim is
also affected by variables such as the load in
the boat, sea conditions, and running speed.

WARNING

EWM00740

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make
steering the boat more difficult. This in-
creases the possibility of an accident. If
the boat begins to feel unstable or is hard
to steer, slow down and/or readjust the

trim angle.

✩✰✬✬✤✤✤✲✣ ✦✧

«
...
37
38
39
40
41
...
»

Содержание VZ200D

















































































Отзывы:

Нет отзывов

Похожие инструкции для VZ200D

Бренд: Navia Страницы: 26

Бренд: Biostar Страницы: 54

Бренд: MSI Страницы: 36

Бренд: Gigabyte Страницы: 36

Бренд: VIA Technologies Страницы: 76

Бренд: Freescale Semiconductor Страницы: 4

Бренд: JETWAY Страницы: 52

Бренд: Maxtang Страницы: 13

Бренд: JETWAY Страницы: 41

Бренд: California Eastern Laboratories Страницы: 34

Бренд: A-Trend Страницы: 44

Бренд: Linear Technology Страницы: 8

Бренд: NXP Semiconductors Страницы: 19

Бренд: Silicon Laboratories Страницы: 12

Бренд: Gigabyte Страницы: 92

73-30130-00877-9

Бренд: Kvaser Страницы: 16

Бренд: Motorola Страницы: 66

Бренд: Motorola Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды