Yamaha Viking YXM70VPHH 2016 Скачать руководство пользователя страница 145

Страница: 145 / 172

8-46

3. Hook the battery bands.
4. Install the air intake duct panel by install-

ing the quick fastener screws.

5. Install the hood.

EBU32650

Jump-starting

Jump-starting the vehicle should be avoided.
The battery should be removed and charged
instead.

WARNING

EWB03430

To avoid battery explosion and/or serious
damage to the electrical system:



Do not connect the negative lead of the
jumper cable to the negative terminal of
the battery.



Do not touch the positive lead of the
jumper cable to the negative lead.



Do not reverse the polarity of the jumper
cables when connecting to the batteries.

However, if the vehicle must be jump-started,
proceed as follows.

1. Turn the key to “

” (off).

2. Remove the hood. (See page 8-10 for

hood removal and installation proce-
dures.)

3. Using a charged 12-volt battery, connect

the positive lead of the jumper cable to
the positive terminal of the battery in the
vehicle and the other end of the positive
lead to the positive terminal of the
charged battery.

1. Jumper cable positive lead

UB427BE0.book Page 46 Friday, February 5, 2016 2:14 PM

Содержание Viking YXM70VPHH 2016













































































































































































Результаты поиска

Содержание Viking YXM70VPHH 2016

Отзывы:

Бренды по названию

Популярные бренды

Yamaha Viking YXM70VPHH 2016, Руководство пользователя

Результаты поиска

Содержание Viking YXM70VPHH 2016

Отзывы:

Бренды по названию

Популярные бренды