Yamaha Viking YXM70VPHH 2016 Скачать руководство пользователя страница 116

Страница: 116 / 172

8-17

2. Remove the final gear oil filler bolt and its

gasket, and then check the oil level in the
final gear case. The oil level should be at
the brim of the filler hole.

3. If the oil is below the brim of the filler hole,

add sufficient oil of the recommended
type to raise it to the correct level.

NOTICE:

Be sure no foreign material

enters the final gear case.

[ECB00422]

4. Check the gasket for damage, and re-

place it if necessary.

5. Install the oil filler bolt and its gasket, and

then tighten the bolt to the specified
torque.

Changing the final gear oil

1. Park the vehicle on a level surface.
2. Place an oil pan under the final gear case

to collect the used oil.

3. Remove the final gear oil filler bolt, the fi-

nal gear oil drain bolt and their gasket to
drain the oil.

1. Final gear oil
2. Gasket
3. Final gear oil filler bolt
4. Correct oil level

Tightening torque:

Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

UB427BE0.book Page 17 Friday, February 5, 2016 2:14 PM

Содержание Viking YXM70VPHH 2016













































































































































































Результаты поиска

Содержание Viking YXM70VPHH 2016

Отзывы:

Бренды по названию

Популярные бренды

Yamaha Viking YXM70VPHH 2016, Руководство пользователя

Результаты поиска

Содержание Viking YXM70VPHH 2016

Отзывы:

Бренды по названию

Популярные бренды