manualshive.com logo in svg

Yamaha TDM900, Руководство пользователя

Поделиться
Скачать
Yamaha TDM900 Скачать руководство пользователя страница 82

PERIODIC MAINTENANCE AND MINOR REPAIR

6-37

6

EAU03497

Replacing a turn signal light 
bulb 

1. Remove the turn signal light lens

by removing the screw.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screw.

ECA00065

CAUTION:

@ 

Do not overtighten the screw, other-
wise the lens may break. 

@

EAU01579

Supporting the motorcycle 

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

1. Screw
2. Turn signal light lens

1. Turn signal light bulb

U5PSE0.book  Page 37  Thursday, December 13, 2001  4:29 PM

Содержание TDM900















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды