Yamaha TDM900 Скачать руководство пользователя страница 74

Страница: 74 / 110

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

EAU04034

Checking and lubricating the
throttle grip and cable

The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated or
replaced at the intervals specified in
the periodic maintenance chart.

EAU03370

Checking and lubricating the
brake and shift pedals

The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.

EAU03164

Checking and lubricating the
brake and clutch levers

The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.

Recommended lubricant:

Lithium-soap-based grease
(all-purpose grease)

Recommended lubricant:

Lithium-soap-based grease
(all-purpose grease)

U5PSE0.book Page 29 Thursday, December 13, 2001 4:29 PM

Содержание TDM900















































































































Результаты поиска

Содержание TDM900

Отзывы:

Бренды по названию

Популярные бренды

Yamaha TDM900, Руководство пользователя

Результаты поиска

Содержание TDM900

Отзывы:

Бренды по названию

Популярные бренды