Yamaha SXV70G Скачать руководство пользователя страница 70

Страница: 70 / 96

8-17

4. Reinstall the dipstick and fit the loop

of the dipstick

handle onto the projection

of the gear case.

Chain tension adjustment

1. Loosen locknut.
2. Turn the adjuster bolt clockwise until it is finger tight.
3. Hold the adjuster bolt in place while tightening the

chain adjuster locknut.

Locknut

Adjuster bolt

ESU00174

Checking the brake pads

Check the brake pads for wear.
If the brake pads reach the wear limit, ask a Yamaha
dealer to replace them.

Brake pad wear indicator

ESU00179

Checking the parking brake pads

Check the parking brake pads for wear by measuring the
thickness of the pads.
If the parking brake pads reach the wear limit, ask a
Yamaha dealer to replace them.

Wear limit

: 1.5 mm (0.06 in)

Wear limit

: 1.0 mm (0.04 in)

U8EK10.book Page 17 Tuesday, June 26, 2001 4:35 PM

Содержание SXV70G

































































































Результаты поиска

Содержание SXV70G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha SXV70G, Руководство пользователя

Результаты поиска

Содержание SXV70G

Отзывы:

Бренды по названию

Популярные бренды