Yamaha Star XVS11ATC Скачать руководство пользователя страница 36

Страница: 36 / 104

INSTRUMENT AND CONTROL FUNCTIONS

3-17

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

EAU15312

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

WARNING

EWA10250

If a malfunction is noted, have a
Yamaha dealer check the system be-
fore riding.

U3B812E0.book Page 17 Tuesday, May 15, 2007 2:52 PM

Содержание Star XVS11ATC









































































































Результаты поиска

Содержание Star XVS11ATC

Отзывы:

Похожие инструкции для Star XVS11ATC

Бренды по названию

Популярные бренды

Yamaha Star XVS11ATC, Руководство пользователя

Результаты поиска

Содержание Star XVS11ATC

Отзывы:

Похожие инструкции для Star XVS11ATC

Бренды по названию

Популярные бренды