Yamaha Star XVS11ATC Скачать руководство пользователя страница 30

Страница: 30 / 104

INSTRUMENT AND CONTROL FUNCTIONS

3-11

EAU14201

Seats
(XVS11AWX/XVS11ATX)

Passenger seat

To remove the passenger seat
Remove the nut and washer, and then
pull the passenger seat up.

To install the passenger seat

1. Insert the projection on the front of

the passenger seat into the holder
as shown and place the seat in the
original position.

2. Install the washer and nut, and

then tighten the nut to the specified
torque.

Rider seat

To remove the rider seat

1. Remove the passenger seat.
2. Remove the bolt, and then pull the

rider seat up.

To install the rider seat

1. Insert the projections on the front

of the rider seat into the holders as
shown, place the seat in the origi-
nal position, and then install the
bolt.

1. Nut

2. Washer

Tightening torque:

Passenger seat nut:

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

1. Projection

2. Seat holder

1. Bolt

1. Projection

2. Seat holder

U3B812E0.book Page 11 Tuesday, May 15, 2007 2:52 PM

Содержание Star XVS11ATC









































































































Результаты поиска

Содержание Star XVS11ATC

Отзывы:

Похожие инструкции для Star XVS11ATC

Бренды по названию

Популярные бренды

Yamaha Star XVS11ATC, Руководство пользователя

Результаты поиска

Содержание Star XVS11ATC

Отзывы:

Похожие инструкции для Star XVS11ATC

Бренды по названию

Популярные бренды