background image

CONSUMER INFORMATION

9-8

9

WARRANTY QUESTIONS AND ANSWERS

What costs are my responsibility during the warranty period?
The customer’s responsibility includes all costs of normal maintenance services, 
non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, 
spark plugs, and brake shoes.

What are some examples of “abnormal” strain, neglect, or abuse?
These terms are general and overlap each other in areas. Specific examples 
include: Running the machine out of oil, sustained high rpm, full-throttle, operating 
the machine with a broken or damaged part which causes another part to fail, 
damage or failure due to improper or careless transportation and/or tie-down. If 
you have any specific questions on operation or maintenance, please contact your 
dealer for advice.

Does the warranty cover incidental costs such as towing or transportation due to
a failure?
No. The warranty is limited to repair of the machine itself.

May I perform any or all of the recommended maintenance shown in the Owner’s 
Manual instead of having the dealer do them?
Yes, if you are a qualified mechanic and follow the procedures specified in the 
Owner’s and Service Manual. We do recommend, however, that items requiring 
special tools or equipment be done by a Yamaha motorcycle dealer.

Will the warranty be void or cancelled if I do not operate or maintain my new 
motorcycle exactly as specified in the Owner’s Manual?
No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” 

However, 

if a particular failure is caused by operation or maintenance other than as 
described in the Owner’s Manual, that failure may not be covered under 
warranty.

What responsibility does my dealer have under this warranty?
Each Yamaha motorcycle dealer is expected to:

Completely set up every new machine before sale.
Explain the operation, maintenance, and warranty requirements to your 
satisfaction at the time of sale, and upon your request at any later date.
Each Yamaha motorcycle dealer is held responsible for his setup, service and 
warranty repair work.

Is the warranty transferable to second owners?
Yes. The remainder of the existing warranty can be transferred upon request. The 
unit has to be inspected and re-registered by an authorized Yamaha motorcycle 
dealer for the policy to remain effective.

CUSTOMER SERVICE

If your machine requires warranty service, you must take it to any authorized Yamaha 
motorcycle dealer within the continental United States. Be sure to bring your warranty 
registration card or other valid proof of the original date of purchase. If a question or 
problem arises regarding the warranty, first contact the owner of the dealership. Since 
all warranty matters are handled at the dealer level, this person is in the best position to 
help you. IF you are still not satisfied and require additional assistance, please write to:

YAMAHA MOTOR CORPORATION, U.S.A.

CUSTOMER RELATIONS DEPARTMENT

P.O. Box 6555

Cypress, California 90630

When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any 
important information such as names, addresses, model, V.I.N. (frame number), 
dates, and receipts.

CHANGE OF ADDRESS

The federal government requires each manufacturer of a motor vehicle to maintain a 
complete, up-to-date list of all first purchasers against the possibility of a safety-
related defect and recall. This list is compiled from the purchase registrations sent to 
Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.

If you should move after you have purchased your new motorcycle, please advise us 
of your new address by sending a postcard listing your motorcycle model name, V.I.N. 
(frame number), dealer number (or dealer’s name) as it is shown on your warranty 
card, your name and new mailing address. Mail to:

YAMAHA MOTOR CORPORATION, U.S.A.

P.O. Box 6555

Cypress, California 90630

Attention: Warranty Department

This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration 
record in accordance with federal law.

Q.
A.

Q.
A.

Q.

A.

Q.

A.

Q.

A.

Q.
A.

1.
2.

3.

Q.
A.

U2UJ1GE0.book  Page 8  Friday, May 11, 2007  10:23 AM

Содержание Star XV250C



































































































Отзывы: