20
1.3
Channel mode messages
These messages specify the basic operation of a part.
1.3.1 All Sound Off
This message silences all currently-sounding notes on the corresponding channel.
However, the settings of channel messages such as Hold 1 and Sostenuto will be
maintained.
Control#
Parameter
Data Range
120
All Sound Off
0
1.3.2 Reset All Controllers
This message resets the following controllers to their default values.
The following data is not changed.
Parameter values specified by program change, bank select MSB/LSB, volume, pan, effect
send levels 1, 3, 4, RPN and NRPN.
Control#
Parameter
Data Range
121
Reset All Controllers
0
1.3.3 All Note Off
This message turns off all notes which are currently on for the corresponding part.
However, if Hold 1 or Sostenuto are on, notes will continue to sound until these are turned
off.
Control#
Parameter
Data Range
123
All Note Off
0
1.3.4 Omni Off
Perform the same processing as when All Note Off is received.
Control#
Parameter
Data Range
124
Omni Off
0
1.3.5 Omni On
Perform the same processing as when All Note Off is received.
Control#
Parameter
Data Range
125
Omni On
0
1.3.6 Mono
Perform the same processing as when All Sound Off is received, and if the value (mono
number) is in the range of 0...16, set the corresponding channel to Mode4* (m = 1).
Control#
Parameter
Data Range
126
Mono
0...16
*Mode4 is a state in which only channel messages on the specified channel will be
received, and notes will be sounded individually (monophonically).
1.3.7 Poly
Perform the same processing as when All Sound Off is received, and set the
corresponding channel to Mode3*.
Control#
Parameter
Data Range
127
Poly
0
*Mode3 is when channel messages will be received only on the specified channel, and will
be sounded polyphonically.
1.4
Program change
This message reports sound selection changes and changes the program number of the
receiving channel.
In order to include changes to the voice bank, Program Change and Bank Select
messages must be sent as a set (see 1.2.1).
When RevPROGRAM CHANGE = OFF for Multi Part Parameter, the program change for
that part is not received.
Not received when Receive Program Change in Native System Parameters is set to off.
1.5
Pitch bend
This message conveys movements of the pitch bender.
This message is generally used to modify the pitch of a part, but the depth of the following
seven effects can be controlled.
The effect of this message can be modified by the following parameters.
• Multi Part Parameter
1. BEND PITCH CONTROL
2. BEND FILTER CONTROL
3. BEND AMPLITUDE CONTROL
4. BEND LFO PMOD DEPTH
5. BEND LFO FMOD DEPTH
6. BEND LFO AMOD DEPTH
• Effect1 Parameter
7. BEND VARIATION CONTROL DEPTH
(Valid when Variation Effect is assigned to a part as Insertion)
By default, the Pitch Control effect is applied.
If the receive channel is a drum part, effects 5 and 6 will not apply.
If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part will not receive
pitch bend messages.
1.6
Channel aftertouch (Receive only)
This message conveys the pressure which is applied to the keyboard after playing a note
in order to create tonal changes (for an entire MIDI channel).
The pressure can be controlled for each part. This message will affect the currently-
sounding notes.
The effect of this message will be determined by the settings of the following parameters.
• EMulti Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO FMOD DEPTH
6. CAT LFO AMOD DEPTH
• Effect1 Parameter
7. CAT VARIATION CONTROL DEPTH
(Valid when the Variation Effect is assigned to a part as Insertion)
By default, there will be no effect.
If the receive channel is a drum part, effects 5 and 6 will not apply.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part will not receive
Channel Aftertouch.
1.7
Polyphonic aftertouch (Receive only)
This message conveys the pressure that is applied to the keyboard after playing a note (for
individual note numbers).
The pressure can be controlled independently for each note. This message will affect
currently-sounding notes.
The effect of this message is determined by the following Multi Part parameters.
1. PAT PITCH CONTROL
2. PAT FILTER CONTROL
3. PAT AMPLITUDE CONTROL
4. PAT LFO PMOD DEPTH
5. PAT LFO FMOD DEPTH
6. PAT LFO AMOD DEPTH
By default, there will be no effect.
The effect will apply to note numbers 36...97.
In the case of either of the following Multi Part parameter settings, that part will not receive
Polyphonic Aftertouch.
Rcv CHANNEL AFTER TOUCH = OFF
PART MODE = DRUM, DRUMS1, 2
2.
System exclusive messages
2.1
Parameter changes
This devices uses the following parameter changes.
[UNIVERSAL REALTIME MESSAGE]
1) Master Volume
[UNIVERSAL NON REALTIME MESSAGE]
1) General MIDI System On
[XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Effect1 parameter change
4) Multi Part parameter change
5) Drums Setup parameter change
[NATIVE PARAMETER CHANGE]
1) Native System parameter change
2) Remote Switch parameter change
3) Normal Voice parameter change
4) Drum Voice parameter change
[Others]
1) Master tuning
Controller
Value
Pitch bend change
±0 (center)
Channel Aftertouch
0 (off)
Polyphonic Aftertouch
0 (off)
Modulation
0 (off)
Expression
127 (maximum)
Hold
0 (off)
Portamento
0 (off)
Sostenuto
0 (off)
Soft pedal
0 (off)
Portamento control
Reset the portamento source note number that was received.
RPN
Number unset, internal data is not affected.
NRPN
Number unset, internal data is not affected.
