80
En
SET MENU
■
Speaker distance
C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
Unit
UNIT
Choices: meters (m),
feet
(ft)
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
• Select “meters” to adjust speaker distances in meters.
• Select “feet” to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
• Select “FRONT L” to adjust the distance of the front
left speaker.
Initial setting: 3.00 m (10.0 ft)
• Select “FRONT R” to adjust the distance of the front
right speaker.
Initial setting: 3.00 m (10.0 ft)
• Select “CENTER” to adjust the distance of the center
speaker.
Initial setting: 3.00 m (10.0 ft)
• Select “SUR. L” to adjust the distance of the surround
left speaker.
Initial setting: 3.00 m (10.0 ft)
• Select “SUR. R” to adjust the distance of the surround
right speaker.
Initial setting: 3.00 m (10.0 ft)
• Select “SUR. B” to adjust the distance of the surround
back speaker.
Initial setting: 2.10 m (7.0 ft)
• Select “SWFR” to adjust the distance of the subwoofer.
Initial setting: 3.00 m (10.0 ft)
“CENTER”, “SUR.L”, “SUR.R”, “SUR.B” and “SWFR” cannot
be adjusted if “CENTER SP” (see page 78), “SUR. L/R SP” (see
page 78), “SUR. B SP” (see page 78) and “LFE/BASS OUT” (see
page 78) are set to “NONE” respectively.
■
Center graphic equalizer
D)CENTER GEQ
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: –6 to +6 dB
Control step: 0.5 dB
Initial setting: 0 dB
Test tone
TEST
Choices:
OFF
, ON
• Select “OFF” to stop test tones and output the currently
selected source component.
• Select “ON” to output test tones from the front left and
center speakers, and adjust the tonal quality of the
center speaker.
y
Press
u
/
d
to select a frequency band and
j
/
i
to adjust the
selected frequency band.
■
Low-frequency effect level
E)LFE LEVEL
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to
0
dB
Control step: 1 dB
Speaker
SPEAKER
Adjusts the speaker LFE level.
Headphone
HEADPHONE
Adjusts the headphone LFE level.
Depending on the settings of “LFE/BASS OUT” (see page 78),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
Note
.
UNIT
;;;;;;;;
feet
FRONTL
;;;
10.0ft
FRONTR
;;;
10.0ft
CENTER
;;;;
10.0ft
[]/[]:Up/Down
[<]/[>]:Adjust
C)SP DISTANCE
p
p
Note
.
TEST>OFFON
100Hz
;;;;;;
0dB
300Hz
;;;;;;
0dB
1kHz
;;;;;;
0dB
3kHz
;;;;;;
0dB
10kHz
;;;;;;
0dB
[]/[]:Up/Down
[<]/[>]:Adjust
D)CENTER GEQ
-
p
p
.
SPEAKER
;;;;;;
0dB
HEADPHONE
;;;;
0dB
[]/[]:Up/Down
[<]/[>]:Adjust
E)LFE LEVEL
p
p
