background image

- 7 -

4

  Connect the YPAO microphone to the YPAO MIC jack on the front panel. 

YPAO microphone

“MIC ON. YPAO START” appears on the front panel display, and then changes to display the following.

VOL.

SW
C

L
SL

SR

R

Press [SETUP]

YPAO

This completes preparations. To achieve more accurate results, be careful of the following when 
measuring. 
•  Measuring will take approximately three minutes. Keep the room as quiet as possible during 

measurement. 

•  Wait in the corner of the listening room during measurement or leave it entirely, to avoid 

becoming an obstruction between the speakers and the YPAO microphone. 

5

 Press 

SETUP

 on the remote control to start measurement.  

VOL.

SW
C

L
SL

SR

R

 Progress  00%

YPAO

Progress

The following display appears if measurement fi nishes without any problems. 

VOL.

SW
C

L
SL

SR

R

YPAO Complete

YPAO

Note

When a problem occurs, an error message or a warning message appears either during or 
after measurement. Refer to “Set up the speaker parameters automatically (YPAO)” in Owner’s 
Manual to solve the problem, and carry out YPAO again. 

6

 Press 

ENTER

 on the remote control to apply the results of measurement. 

SW
C

L
SL

SR

R

Disconnect MIC

YPAO

VOL.

7

  Remove the YPAO microphone.  

YPAO fi nishes automatically when the YPAO microphone is removed. 

DOCK

DOCK

SETUP

RECEIVER 

A

ENTER

Содержание RX-V371BL









Отзывы: