2
RX-V1500/
DSP-AX1500
RX-V1500/DSP-AX1500
WALL
OUTLET
EQUIPMENT
UNDER TEST
AC LEAKAGE
TESTER OR
EQUIVALENT
INSULATING
TABLE
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and
possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
■
TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked
s
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
●
Meter impedance should be equivalent to 1500 ohm shunted
by 0.15
µ
F.
“CAUTION”
“F1, F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A,
125V FUSE.”
CAUTION
F1, F2: REPLACE WITH SAME TYPE 10A, 125V FUSE.
ATTENTION
F1, F2: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 125V.
●
Leakage current must not exceed 0.5mA.
●
Be sure to test for leakage with the AC plug in both polarities.
無鉛ハンダにはいくつかの種類がありますが、修理時には
下記のような無鉛ハンダの使用を推奨します。
・Sn+Ag+Cu(錫+銀+銅)
・Sn+Cu(錫+銅)
・Sn+Zn+Bi(錫+亜鉛+ビスマス)
注意:
① 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ30
〜40℃程度高くなっていますので、それぞれのハンダ
に合ったハンダごてをご使用ください。
Among some types of lead free solder currently available,
it is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
1. As the melting point temperature of the lead free solder
is about 30
°
C to 40
°
C (50
°
F to 70
°
F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.
About Lead Free Solder /
無鉛ハンダについて
The P.C.B.s installed in this unit are soldered using the
following solder.
本機に搭載されている基板のハンダ付けに使用されている
ハンダは下記の通りです。
DSP P.C.B.
FUNCTION P.C.B.
OPERATION P.C.B.
MAIN P.C.B.
POWER PC.B.
VIDEO P.C.B.
CONVERSION P.C.B.
A 面
鉛入りハンダ
鉛入りハンダ
ー
ー
ー
ー
鉛入りハンダ
B 面
無鉛ハンダ
無鉛ハンダ
無鉛ハンダ
無鉛ハンダ
無鉛ハンダ
無鉛ハンダ
無鉛ハンダ
DSP P.C.B.
FUNCTION P.C.B.
OPERATION P.C.B.
MAIN P.C.B.
POWER PC.B.
VIDEO P.C.B.
CONVERSION P.C.B.
Side A
Lead Solder
Lead Solder
-
-
-
-
Lead Solder
Side B
Lead Free Solder
Lead Free Solder
Lead Free Solder
Lead Free Solder
Lead Free Solder
Lead Free Solder
Lead Free Solder
Side A
Side B
SMT
REFLOW
Process
MI
FLOW
Process
Solder Dip