RS7000
46
screen, the "22. Factory set" screen will appear, and if you press
the [EXIT] button, the "23. Exit" screen will appear.
(D) Proceeding through the tests
When you enter the test program, the following screen will appear
first.
Press the [F3] button (-1) to select and display the test item that
precedes the currently selected test.
Press the [F4] button (+1) to select and display the test item
that follows the currently selected test.
Press the [ENTER] key to execute the selected test.
Press the [EXIT] button to execute "23. Exit".
(E) Proceeding to the next test if a result is NG
If a test returns a result of NG (error), you can either press the
[EXIT] button to return to the test item selection screen and
perform the test again, or you can perform another test.
However, this method cannot be used for the [EXIT] button test
in "4. Panel switches, rotary switches."
1. RAM battery
When you enter the test, the voltage of the RAM backup battery
will be checked to see whether it is OK (2.95V and less than
3.50 V) or NG.
The result will be displayed in the LCD, the test will end, and
you will be able to select another test item.
(A) Test program list
(B) Preparation
The following test equipment and items are required in order to
test the RS7000.
Test equipment: frequency counter, oscilloscope, level meter
(JIS-C curve), distortion meter (flat), keyboard
amplifier etc.
Other items:
foot switch, MIDI cable, digital audio cable,
AIEB2, SCSI (50 pin) hard disk drive etc.
(C) Entering the test program
While holding down the [P[PATT CHAIN]+[UTILITY]
buttons, turn on the power. The following screen will appear in
the LCD.
From this screen, press the [ENTER] button, and the test
program will start up. If you press the [STORE] button from this
Test no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Test item
RAM battery
LCD, LED blink
LED
Panel switches, rotary switches
Encoders 1--4
Knobs 1--22
Pads 1--2, foot switch
MIDI IN/OUT A
MIDI IN/OUT B
1 kHz OUTPUT L sound
1 kHz OUTPUT R sound
A/D -> D/A (MIC)
A/D -> D/A (LINE)
Card
SCSI
Digital In -> D/A
Optical In -> D/A
SIMM
SIMM (Full)
SYSTEM ROM, Wave ROM
SYSTEM RAM, Wave RAM
Factory set
Exit
TEST PROGRAM
//// RS7000 Test Program ////
Firm
Ver :x.xx
Kernel Ver :x.xx
Data
Ver :x.xx
* [ENTER] :Test Start
* [STORE] :Factory Set
* [EXIT]
:Exit
//// RS7000 Test Program ////
01:Battery
:Press [ENTER]
[-1] [+1]
//// RS7000 Test Program ////
01:Battery
:Press [ENTER]
[-1] [+1]
POWER
ON / OFF
//// RS7000 Test Program ////
01:Battery
:OK
3.2v
[-1] [+1]
(Test result display)
OK
Содержание RS7000 Ver.1.2
