Yamaha RCX222 Скачать руководство пользователя страница 404

Страница: 404 / 524

5-16

Chapter

PARALLEL I/O INTERF

ACE

5-17

■

The SWI command was executed by

(DIRECT) in "AUTO" mode.

(Reset (off) does not occur if the SWI statement was executed in the program.)

■

The online commands @RESET, @INIT PGM, @INIT MEM, @INIT ALL,

or @SWI were executed.

■

The HALT statement was executed in the program.

1.9 Dedicated I/O signal timing charts

1.9.1 Turning the power on

■

Turning the power on (while emergency stop input is on)

Approx. 3 sec.

Control power

DI00

(in SAFETY

connector)

Emergency stop
ready signal

DO00

Emergency stop

contact monitor

MPRDY

(in SAFETY

connector)

Main power ON
ready

Main power

DO01

CPU OK

DO02

Servo-on state

DO03

Alarm

• MPRDY (Main power ON ready) turns on after the control power supply turns on.

Then turn on the main power to the external device.

• After DO01 (CPU OK) turns on, the robot servo turns on and then DO02 (Servo-on

state) turns on. However, if serial IO setting or "SAFE" mode is enabled, the robot

starts with the servo turned off.

1. Standard I/O interface overview

Содержание RCX222













































































































































































































































































































































































































































































































































Результаты поиска

Содержание RCX222

Отзывы:

Похожие инструкции для RCX222

Бренды по названию

Популярные бренды

Yamaha RCX222, Руководство пользователя

Результаты поиска

Содержание RCX222

Отзывы:

Похожие инструкции для RCX222

Бренды по названию

Популярные бренды