Yamaha R1 Series 2015 Скачать руководство пользователя страница 189

Страница: 189 / 704

PERIODIC MAINTENANCE

3-15

WARNING

EWA17050

• After adjusting the brake lever position,

make sure the pin on the brake lever holder

is firmly inserted in the hole in the adjusting

dial.

• A soft or spongy feeling in the brake lever

can indicate the presence of air in the brake

system. Before the vehicle is operated, the

air must be removed by bleeding the brake

system. Air in the brake system will consid-

erably reduce brake performance resulting

in loss of control and possibly cause an ac-

cident. Therefore, check and if necessary,

bleed the brake system.

NOTICE

ECA13490

After adjusting the brake lever position,

make sure there is no brake drag.

EAS30633

CHECKING THE FRONT BRAKE PADS

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

•

Front brake pad
Wear indicators “1” almost touch the brake
disc

Replace the brake pads as a set.

Refer to “FRONT BRAKE” on page 4-43.

EAS30631

ADJUSTING THE REAR DISC BRAKE

1. Adjust:

•

Brake pedal position

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen the locknut “1”.
b. Turn the adjusting bolt “2” in direction “a” or

“b” until the specified brake pedal position is
obtained.

WARNING

EWA13070

After adjusting the brake pedal position,

check that the end of the adjusting bolt “c” is

visible through the hole “d”.

c. Tighten the locknut “1” to specification.

WARNING

EWA17030

A soft or spongy feeling in the brake pedal

can indicate the presence of air in the brake

system. Before the vehicle is operated, the

air must be removed by bleeding the brake

system. Air in the brake system will consid-

erably reduce braking performance.

NOTICE

ECA13510

After adjusting the brake pedal position,

make sure there is no brake drag.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Adjust:

•

Rear brake light switch
Refer to “ADJUSTING THE REAR BRAKE
LIGHT SWITCH” on page 3-36.

EAS30634

CHECKING THE REAR BRAKE PADS

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

•

Rear brake pad
Wear indicator grooves “1” almost disap-
peared

Replace the brake pads as a set.

Direction “a”

Brake pedal is raised.

Direction “b”

Brake pedal is lowered.

Rear brake master cylinder lock

nut

16 Nm (1.6 m·kgf, 12 ft·lbf)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды