Yamaha PW-SE series Скачать руководство пользователя страница 51

Страница: 51 / 60

TROUBLESHOOTING

E-Bike Systems

Symptom

Check

Action

Pedaling is difficult.

Is the display unit’s

power on?

Press the power switch on the display

unit to turn the power on.

Is the battery pack

installed?

Install a charged battery pack.

Is the battery pack

charged?

Charge the battery pack.

Has the bicycle

remained stationary for

5 minutes or longer?

Turn the power on again.

Are you riding on a long

inclined road or carrying

a heavy load during

summertime?

This is not a malfunction. It is a

safeguard engaged when the

temperature of the battery pack or the

Drive Unit is too high. Power assist will

be restored once the temperature of the

battery pack or the Drive Unit has

decreased. Also, you can make this less

likely to occur by shifting to a lower gear

than you would usually use (for example,

by shifting from second to first gear).

Is the air temperature

low (roughly 10 °C or

below)?

During the wintertime, store the battery

pack indoors before use.

Are you charging the

battery pack while it is

mounted on the

bicycle?

Stop charging the battery pack.

The Drive Unit turns

on and off while

riding.

Is the battery pack

correctly installed?

Check to make sure the battery pack is

locked in place.

If this problem still occurs with the

battery pack firmly locked in place, there

may be a loose connection with the

battery pack terminals or wires. Have an

authorized dealer inspect your bicycle.

Strange rumbling or

crunching noises

come from the Drive

Unit.

There could be a problem inside the

Drive Unit.

Smoke or unusual

odor comes from the

Drive Unit.

There could be a problem inside the

Drive Unit.

Содержание PW-SE series





























































Результаты поиска

Содержание PW-SE series

Отзывы:

Похожие инструкции для PW-SE series

Бренды по названию

Популярные бренды

Yamaha PW-SE series, Оригинальное руководство пользователя

Результаты поиска

Содержание PW-SE series

Отзывы:

Похожие инструкции для PW-SE series

Бренды по названию

Популярные бренды