Yamaha PSR-S710, Руководство по обслуживанию

Страница: 62 / 162

PSR-S710/PSR-S910
62
Test No. LCD display Test descriptions, judging conditions, etc.
6 006 : Effect RAM Check1
OK:
006 : Effect RAM Check1
OK
NG:
006 : Effect RAM Check1
TG1 (IC
***
) NG
***
: Location Number of IC
Checking the Effect RAM connected to the TG bus. (Simpli fi ed check)
Check that “Effect RAM Check1 OK” is displayed on LCD.
Case PSR-S710 Case PSR-S910
TG1 (IC305) NG TG1 (IC306) NG
7 007 : TG 1 Check
OK:
007 : TG 1 Check
End
Checking the tone generator 1.
Sequentially outputs the sine wave starting from the low keys and switching sounds of the tone generator.
(32 notes from C2 to G4) Check that there is no abnormal sounds or noise.
“TG 1 Check End” will appear when the test is over.
10 010 : Pitch Check
Checking sound pitch.
Pitch accuracy check:
Connect a frequency counter to the [PHONES] jack. (Either L or R)
When the test is started, a sine wave of (441 ± 0.2 Hz) will be played. (PAN=Center)
Amount of volume decay:
Connect a level meter (with a JIS-C fi lter) to the L/R of the [PHONES] jacks.
Set the [MASTER VOLUME] to the minimum. Load should be 33 Ω .
Check that the amount of decay is 75.0 dB or more for both L and R of the [PHONES] jack.
11 011 : Output R Check Checking the R channel output.
Connect a level meter (with a JIS-C
fi lter) to each jack. (PHONES L, R, OUTPUT L/L+R, R)
Set the [MASTER VOLUME] to the maximum level and check the output level of the R channel.
(1 KHz sine wave, PAN=R) (PHONES L, R: 33
Ω load, OUTPUT L/L+R, R: 10 k Ω load (2 monaural
jacks used simultaneously))
· PHONES L:
-45.0 dBu or less PHONES R: -2.6 ± 2 dBu
· OUTPUT L/L+R: -40.0 dBu or less OUTPUT R: +9.1 ± 2 dBu
12 012 : Output L Check
Checking the L channel output.
Connect a level meter (with a JIS-C
fi lter) to each jack. (PHONES L, R, OUTPUT L/L+R, R)
Set the [MASTER VOLUME] to the maximum level and check the output level of the L channel.
(1 KHz sine wave, PAN = L) (PHONES L, R: 33
Ω load, OUTPUT L/L+R, R: 10 k Ω load (2 monaural
jacks used simultaneously))
· PHONES L:
-2.6 ± 2 dBu PHONES R: -45.0 dBu or less
· OUTPUT L/L+R: +9.1 ± 2 dBu OUTPUT R: -40.0 dBu or less
Noise Level
After the test 12 is completed, connect the level meter (with a JIS-C fi lter) to the L/R of the [PHONES]
jacks and check the noise level. (PHONES L, R: 33 Ω load)
· PHONES L: -80.0 dBu or less PHONES R: -80.0 dBu or less
13 013 : EQ Low Check Checking EQ-LOW frequency. Check that sine wave at about 65.4 Hz (C1) is output with speci fi ed level
and PAN=Center. Sound production stops when returning to the selection screen with the [START/STOP]
button.
14 014 : EQ Mid Check
Checking EQ-MID frequency. Check that sine wave at about 523 Hz (C4) is output with speci fi ed level
and PAN=Center. Sound production stops when returning to the selection screen with the [START/STOP]
button.
15 015 : EQ High Check
Checking EQ-HIGH frequency. Check that sine wave at about 4186 Hz (C7) is output with speci fi ed level
and PAN=Center. Sound production stops when returning to the selection screen with the [START/STOP]
button.
18 018 : MUTE Check
MUTE OFF:
018 : MUTE Check
OFF
MUTE ON:
018 : MUTE Check
ON
Checking MUTE. Set the [MASTER VOLUME] to the maximum level.
Connect a level meter (with a JIS-C
fi lter) to the L/R of the [PHONES] jack. (33 Ω load) When the test is
started with the [START/STOP] button, sounds can be played (MUTE OFF) and “MUTE Check OFF” is
displayed on the LCD.
Mute sounds (MUTE ON) with the [TAB
2
] button and “MUTE Check ON” is displayed on the LCD.
Cancel the mute function (MUTE OFF) with the [TAB
3
] button and “MUTE Check OFF” is displayed
on the LCD.
Check output level when [MUTE ON] is selected.
PHONES L, R: -80.0 dBu or less