Front & Rear Panels
MG206C-USB/MG166CX-USB/MG166C-USB Owner’s Manual
Reference
22
B
Level Meter
This LED meter displays the level of the signal selected by
the MONITOR switch
E
, 2TR IN/USB switch
F
and PFL
switch. The “0” segment corresponds to the nominal output
level. The PEAK indicator lights red when the output
reaches the clipping level.
C
RETURN
• AUX1, AUX2 Control
Adjusts the level at which the L/R signal received at the
RETURN jacks (L (MONO) and R) is sent to the AUX1 and
AUX2 buses.
• STEREO Control
Adjusts the level at which the signal received at the
RETURN jacks (L (MONO) and R) is sent to the STEREO
L/R bus.
• If you supply a signal to the RETURN L (MONO)
jack only, the mixer sends the same signal to both
the L and R STEREO buses.
• (MG206C-USB) Signals input via the RETURN1
jacks are adjusted using the RETURN1 AUX1,
AUX2 and the STEREO controls, and signals input
via the RETURN2 jacks are adjusted using the
RETURN2 AUX1, AUX2 and the STEREO controls.
D
Master SEND Controls (AUX, EFFECT)
Adjusts the signal level sent to the SEND (AUX, EFFECT)
jacks.
If you are using the MG166CX-USB, the Master
SEND control (EFFECT) does not affect the level of
the signal sent from the EFFECT bus to the internal
digital effect processor.
E
MONITOR/PHONES
• MONITOR switches
These switches select the signal sent to the MONITOR OUT
jacks, PHONES jack and the level meter from STEREO L/R
bus, GROUP 1/2 bus or GROUP 3/4 bus.
STEREO L/R bus:
STEREO (
)
GROUP 1/2 bus:
GROUP (
), 1-2 (
)
GROUP 3/4 bus:
GROUP (
), 3-4 (
)
• MONITOR Control
Controls the level of the signal output to the PHONES jack
and the MONITOR OUT jacks.
F
2TR IN/USB
• 2TR IN/USB Switch
If this switch is set to TO MONITOR (
), the signals input
via the 2TR IN jacks and the USB connector are sent to the
MONITOR OUT jacks, the PHONES jack, and the level
meter. If it is set to TO STEREO (
), the signals are sent to
the STEREO L/R bus.
• 2TR IN/USB Control
Adjusts the level of the signal sent from the 2TR IN jacks
and the USB connector.
The following illustration shows how the switch settings cor-
respond to the signal selection.
*
: When overdubbing, you can adjust the levels of the mon-
itor playback signal and the signal being recorded separately.
MONITOR MIX Signal Flow
If the input channel PFL switch is on (
), then only
the PFL output from that channel is sent to the MON-
ITOR OUT jacks, PHONES jack, and level meter.
G
GROUP 1-2 Fader
Adjusts the signal level sent to the GROUP OUT 1/2 jacks.
H
GROUP 3-4 Fader
Adjust the signal level to the GROUP OUT 3/ 4 jacks.
I
ST Switch
If this switch is on, the signals are sent to the STEREO L/R
bus via the GROUP 1-2 fader or GROUP 3-4 fader. The
GROUP 1 and 3 signals go to STEREO L and the GROUP 2
and 4 signals go to STEREO R.
J
STEREO OUT Master Fader
Adjusts the signal level sent to the STEREO OUT jacks.
NOTE
NOTE
Switches
Signals output via the
MONITOR/PHONES
jacks
PFL
MONITOR/
PHONES
2TR IN/USB
ON
—
—
PFL
OFF
STEREO
TO STEREO STEREO
(+ 2TR IN/USB)
TO MONITOR 2TR IN/USB
*
GROUP
1-2
TO STEREO
GROUP 1-2
TO MONITOR GROUP 1-2
(+ 2TR IN/USB)
3-4
TO STEREO
GROUP 3-4
TO MONITOR GROUP 3-4
(+ 2TR IN/USB)
Playback
signal
Recording
signal
2TR IN/USB
2TR IN/USB control
STEREO OUT Master fader
MONITOR/PHONES controls
STEREO
bus
REC OUT/USB
jacks
MONITOR
OUT/PHONES
jacks
NOTE
