
17
MG12/4
MG16/4
3.
PS Circuit Board
(Time required : About 4 min.)
3-1.
Remove the rack mount angle L and R.
(See procedure 1)
3-2.
Remove the bottom cover. (See procedure 2)
3-3.
Remove the two (2) screws marked [480]. The PS circuit
board and heat sink can then be removed. (Fig. 2)
*
Replacing any part on the PS circuit board requires
removal of the heat sink as well. Use the following
procedure to remove the heat sink.
3-4.
Remove the two (2) screws marked [A] fixing IC01 and
IC05. (Photo 1)
3-5.
Remove the three (3) screws marked [B]. (Photo 1)
3-6.
Remove the solder IC02, IC03 and Q01. The heat sink
can then be removed from the PS circuit board. (Photo 1)
4.
Side Cover
(Time required : About 5 minutes each.)
4-1.
Remove the rack mount angle L and R.
(See procedure 1)
4-2.
Remove the bottom cover. (See procedure 2)
4-3.
Side Cover L :
4-3-1. Remove the screw marked [430A], two (2) screws
marked [430B], three (3) screws marked [440A] and
two (2) screws marked [450A]. The side cover L can
then be removed. (Fig. 2)
4-4.
Side Cover R :
4-4-1. Remove the PS circuit board. (See procedure 3)
4-4-2. Remove the screw marked [430C], two (2) screws
marked [430D], three (3) screws marked [440B] and
two (2) screws marked [450B]. The side cover R can
then be removed. (Fig. 2)
5.
MAIN Circuit Board, Jack 1/2, 2/2 Circuit
Board
(Time required : About 15 min.)
5-1.
Remove the rack mount angle L and R.
(See procedure 1)
5-2.
Remove the bottom cover. (See procedure 2)
5-3.
Remove the PS circuit board. (See procedure 3)
5-4.
Remove the side cover L and R. (See procedure 4)
5-5.
Pull out the ten (10) fader knobs. (Fig. 2)
5-6.
Remove the two (2) screws marked [450C]. (Fig. 2)
5-7.
Remove the eighteen (18) screws marked [460] and
twenty-six (26) hexagonal nuts. The MAIN and JACK
1/2, 2/2 circuit boards can then be removed. (Fig. 2)
Disconnect the seven (7) connectors and separate the
MAIN circuit board and the JACK 1/2 circuit board.
*
The knobs, buttons and supporting fixtures on the MAIN
circuit board are not components of the circuit board.
When replacing the MAIN circuit board, be sure to
remove these parts according to the following
procedure.
3.
PSシート
(所要時間:約4分)
3-1.
ラックアングルL、
Rを外します。
(1項参照)
3-2.
ボトムカバーを外します。
(2項参照)
3-3.
[480]のネジ2本を外し、
PSシートとヒートシンクを外
します。
(図2)
※
PSシート上の部品を交換する場合に、ヒートシンクを取り
外す必要もあります。
以下の手順でヒートシンクを取り外し
てください。
3-4.
IC01、IC05を止めている[A]のネジ2本を外します。
(写真1)
3-5.
[B]のネジ3本を外します。
(写真1)
3-6.
IC02、
IC03、
Q01のハンダを取り、
ヒートシンクからPS
シートを外します。
(写真1)
4.
サイドカバー
(所要時間:各約5分)
4-1.
ラックアングルL、
Rを外します。
(1項参照)
4-2.
ボトムカバーを外します。
(2項参照)
4-3.
サイドカバーL:
4-3-1. [430A]のネジ1本、
[430B]のネジ2本、
[440A]のネジ3本、
[450A]のネジ2本を外し、
サイドカバーLを外します。
(図2)
4-4.
サイドカバーR:
4-4-1. PSシートを外します。
(3項参照)
4-4-2. [430C]のネジ1本、
[430D]のネジ2本、
[440B]のネジ3本、
[450B]のネジ2本を外し、
サイドカバーRを外します。
(図2)
5.
MAINシート、
JACK 1/2、
2/2シート
(所要時間:約15分)
5-1.
ラックアングルL、
Rを外します。
(1項参照)
5-2.
ボトムカバーを外します。
(2項参照)
5-3.
PSシートを外します。
(3項参照)
5-4.
サイドカバーL、
Rを外します。
(4項参照)
5-5.
ノブFADERを10個抜き取ります。
(図2)
5-6.
[450C]のネジ2本を外します。
(図2)
5-7.
[460]のネジ18本と特殊六角ナット26個を外し、
MAIN
シートとJACK 1/2、
2/2シートを外します。
(図2)
コネクター7箇所を抜いて、
MAINシートとJACK 1/2
シートを分割します。
※
MAINシート上のノブ、ボタン、サポート金具は、シートの構
成部品ではありません。
MAINシートを交換する際は、
以下の
手順でこれらの部品を取り外してください。