manualshive.com logo in svg

Yamaha MBK MW125 2014, Руководство по обслуживанию

Yamaha MBK MW125 2014 - качественный скутер с мощным двигателем, идеальный для городской езды. Для обслуживания и ухода за ним, вы можете бесплатно скачать сервисный мануал на manualshive.com. Получите необходимое руководство по эксплуатации прямо сейчас!

Поделиться
Скачать
background image

3

PERIODIC CHECKS AND ADJUSTMENTS

PERIODIC MAINTENANCE

............................................................................ 3-1

INTRODUCTION ....................................................................................... 3-1
PERIODIC MAINTENANCE CHART FOR THE EMISSION 

CONTROL SYSTEM ................................................................................ 3-1

GENERAL MAINTENANCE AND LUBRICATION CHART ....................... 3-1
CHECKING THE FUEL LINE .................................................................... 3-4
CHECKING THE SPARK PLUG ............................................................... 3-4
ADJUSTING THE VALVE CLEARANCE .................................................. 3-4
CHECKING THE BREATHER HOSES ..................................................... 3-6
CHECKING THE ENGINE IDLING SPEED .............................................. 3-7
CHECKING THE THROTTLE BODY JOINT AND 

INTAKE MANIFOLD ................................................................................. 3-7

CHECKING THE EXHAUST SYSTEM...................................................... 3-8
ADJUSTING THE EXHAUST GAS VOLUME ........................................... 3-8
REPLACING THE AIR FILTER ELEMENT ............................................... 3-8
CLEANING THE V-BELT CASE AIR FILTER ELEMENT ......................... 3-9
CHECKING THE BRAKE OPERATION .................................................. 3-10
CHECKING THE FRONT BRAKE PADS ................................................ 3-10
CHECKING THE REAR BRAKE PADS .................................................. 3-10
ADJUSTING THE REAR BRAKE LEVER FREE PLAY .......................... 3-10
CHECKING THE FRONT BRAKE HOSES ............................................. 3-11
CHECKING THE REAR BRAKE HOSE .................................................. 3-11
CHECKING THE BRAKE FLUID LEVEL................................................. 3-11
BLEEDING THE HYDRAULIC BRAKE SYSTEM ................................... 3-12
CHECKING THE WHEELS ..................................................................... 3-13
CHECKING THE TIRES.......................................................................... 3-14
CHECKING THE WHEEL BEARINGS .................................................... 3-15
CHECKING AND ADJUSTING THE STEERING HEAD AND 

LOWER BRACKETS .............................................................................. 3-15

CHECKING THE TIE-ROD BUSHINGS AND 

FRONT ARM BUSHINGS ...................................................................... 3-17

CHECKING THE LINK ARM BEARINGS................................................ 3-17
CHECKING THE CHASSIS FASTENERS .............................................. 3-17
LUBRICATING THE LEVERS ................................................................. 3-17
CHECKING THE SIDESTAND................................................................ 3-17
LUBRICATING THE SIDESTAND........................................................... 3-18
CHECKING THE CENTERSTAND ......................................................... 3-18
LUBRICATING THE CENTERSTAND .................................................... 3-18
CHECKING THE SIDESTAND SWITCH................................................. 3-18
CHECKING THE FRONT FORK ............................................................. 3-18
CHECKING THE REAR SUSPENSION.................................................. 3-18
CHECKING THE ENGINE OIL LEVEL.................................................... 3-18
CHANGING THE ENGINE OIL ............................................................... 3-19
CHECKING THE COOLANT LEVEL....................................................... 3-20
CHECKING THE COOLING SYSTEM .................................................... 3-21
CHANGING THE COOLANT................................................................... 3-21
CHANGING THE FINAL TRANSMISSION OIL....................................... 3-22
REPLACING THE V-BELT ...................................................................... 3-23
CHECKING THE BRAKE LIGHT SWITCHES......................................... 3-23
CHECKING AND LUBRICATING THE CABLES .................................... 3-23

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Yamaha MT01X Owner'S Manual preview
MT01X
Бренд: Yamaha Страницы: 92
hepco & becker 6613519 01 01 Quick Start Manual preview
6613519 01 01
Бренд: hepco & becker Страницы: 5
SUOMY C1SF0001 Instructions For User preview
C1SF0001
Бренд: SUOMY Страницы: 84
Fantic Motor TF 250 2012 User Manual preview
TF 250 2012
Бренд: Fantic Motor Страницы: 60
Yamaha PW50 2020 Owner'S Manual preview
PW50 2020
Бренд: Yamaha Страницы: 74
Yamaha PW50 2013 Owner'S Manual preview
PW50 2013
Бренд: Yamaha Страницы: 76
Yamaha PW50(Y) Owner'S Manual preview
PW50(Y)
Бренд: Yamaha Страницы: 72
Yamaha Nouvo AT115S Owner'S Manual preview
Nouvo AT115S
Бренд: Yamaha Страницы: 78
Yamaha Neo's 4 YN50F Owner'S Manual preview
Neo's 4 YN50F
Бренд: Yamaha Страницы: 76
Yamaha NMX GPD125-A Owner'S Manual preview
NMX GPD125-A
Бренд: Yamaha Страницы: 90
Yamaha PW50(S) Owner'S Manual preview
PW50(S)
Бренд: Yamaha Страницы: 164
Yamaha PW50(P) Owner'S Manual preview
PW50(P)
Бренд: Yamaha Страницы: 164
Yamaha PW50(N) Owner'S Manual preview
PW50(N)
Бренд: Yamaha Страницы: 164
Yamaha PW50(R) Owner'S Manual preview
PW50(R)
Бренд: Yamaha Страницы: 164
Yamaha PW50 2008 Owner'S Manual preview
PW50 2008
Бренд: Yamaha Страницы: 66
Palm 11480 Manual preview
11480
Бренд: Palm Страницы: 14
Shad Y0NM15ST Manual preview
Y0NM15ST
Бренд: Shad Страницы: 2
Shad Y0JG52ST Manual preview
Y0JG52ST
Бренд: Shad Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды