Yamaha MBK MW125 2014 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 380

background image

PERIODIC MAINTENANCE

3-24

2. Check:

• Cable operation

Rough movement

→

Lubricate.

TIP

Hold the cable end upright and pour a few drops
of lubricant into the cable sheath or use a suit-
able lubricating device.

EAS30861

CHECKING THE THROTTLE GRIP
OPERATION

1. Check:

• Throttle cables

Damage/deterioration

→

Replace.

• Throttle cable installation

Incorrect

→

Reinstall the throttle cables.

Refer to “HANDLEBAR” on page 4-60.

2. Check:

• Throttle grip movement

Rough movement

→

Lubricate or replace the

defective part(s).

TIP

With the engine stopped, turn the throttle grip
slowly and release it. Make sure that the throttle
grip turns smoothly and returns properly when
released.
Repeat this check with the handlebar turned all
the way to the left and right.

3. Check:

• Throttle grip free play “a”

Out of specification

→

Adjust.

4. Adjust:

• Throttle grip free play

TIP

Prior to adjusting the throttle grip free play, the
engine idling speed should be adjusted properly.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Slide back the rubber cover “1”.
b. Loosen the locknut “2”.
c. Turn the adjusting nut “3” in direction “a” or “b”

until the specified throttle grip free play is ob-
tained.

d. Tighten the locknut.
e. Slide the rubber cover its original position.

TIP

Make sure that the adjusting nut is covered com-
pletely by the rubber cover.

WARNING

EWA17990

After adjusting the throttle grip free play,
start the engine and turn the handlebars to
the right and to the left to ensure that this
does not cause the engine idling speed to
change.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS30663

CHECKING THE SWITCHES, LIGHTS AND
SIGNALS

1. Check that all switches operate and that all

lights come on.
Refer to “INSTRUMENT AND CONTROL
FUNCTIONS” in Owner’s manual.
Faulty

→

Refer to “CHECKING THE

SWITCHES” on page 8-55 and “CHECKING
THE BULBS AND BULB SOCKETS” on
page 8-58.

Recommended lubricant

Engine oil or a suitable cable lu-
bricant

Recommended lubricant

Suitable cable lubricant

Throttle grip free play

3.0–7.0 mm (0.12–0.28 in)

a

Direction “a”

Throttle grip free play is increased.

Direction “b”

Throttle grip free play is decreased.

2

3

1

a

b

«
...
103
104
105
106
107
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: KAYO MOTOR Страницы: 84

Бренд: Öhlins Страницы: 2

Бренд: Regal Raptor Страницы: 48

Бренд: TRS Страницы: 38

LOCK-IT 506007-7

Бренд: hepco & becker Страницы: 2

Бренд: Cycle Protect Страницы: 15

Бренд: Honda Страницы: 143

SPORTTOURING ST4S

Бренд: Ducati Страницы: 313

Бренд: yasuni Страницы: 9

Бренд: Klarfit Страницы: 8

MARATHON 125 AC

Бренд: RIEJU Страницы: 40

Бренд: APRILIA Страницы: 151

Бренд: GhostBikes Страницы: 8

Бренд: ArcOne Страницы: 4

Бренд: SCHUBERTH Страницы: 54

ROADWIN FI - CATALOG

Бренд: DAELIM Страницы: 68

Super head STAGE-1 kit

Бренд: Takegawa Страницы: 12

Бренд: URAL Motorcycles Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды