Yamaha MBK MW125 2014 Скачать руководство пользователя страница 355 | Manualshive

Страница: 355 / 380

background image

ELECTRICAL COMPONENTS

8-58

EAS30550

CHECKING THE BULBS AND BULB
SOCKETS

TIP

Do not check any of the lights that use LEDs.

Check each bulb and bulb socket for damage or
wear, proper connections, and also for continuity
between the terminals.
Damage/wear

→

Repair or replace the bulb,

bulb socket or both.
Improperly connected

→

Properly connect.

No continuity

→

Repair or replace the bulb, bulb

socket or both.

Types of bulbs

The bulbs used on this vehicle are shown in the
illustration.
• Bulbs “a” and “b” are used for the headlights

and usually use a bulb holder that must be de-
tached before removing the bulb. The majority
of these types of bulbs can be removed from
their respective sockets by turning them coun-
terclockwise.

• Bulbs “c” are used for turn signal and tail/brake

lights and can be removed from the socket by
pushing and turning the bulb counterclockwise.

Checking the condition of the bulbs

The following procedure applies to all of the
bulbs.
1. Remove:

• Bulb

WARNING

EWA17540

Since headlight bulbs get extremely hot,
keep flammable products and your hands
away from them until they have cooled
down.

NOTICE

ECA14381

• Be sure to hold the socket firmly when re-

moving the bulb. Never pull the lead, other-
wise it may be pulled out of the terminal in
the coupler.

• Avoid touching the glass part of a headlight

bulb to keep it free from oil, otherwise the
transparency of the glass, the life of the
bulb, and the luminous flux will be adverse-
ly affected. If the headlight bulb gets soiled,
thoroughly clean it with a cloth moistened
with alcohol or lacquer thinner.

2. Check:

• Bulb (for continuity)

(with the pocket tester)
No continuity

→

Replace.

TIP

Before checking for continuity, set the pocket
tester to “0” and to the “

Ω

×

1” range.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the positive tester probe to terminal

“1” and the negative tester probe to terminal
“2”, and check the continuity.

b. Connect the positive tester probe to terminal

“1” and the negative tester probe to terminal
“3”, and check the continuity.

c. If either of the readings indicate no continuity,

replace the bulb.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

«
...
353
354
355
356
357
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

750 Sport Bevel Heaven

Бренд: Ducati Страницы: 235

Бренд: CB Sabbiatrici Страницы: 43

Бренд: P.Lindberg Страницы: 26

Yamaha X-MAX 300

Бренд: BRUUDT Страницы: 7

Rocky Mountain-EXP SB-1

Бренд: Wolfman Страницы: 7

Бренд: CRATONI Страницы: 61

Бренд: Triumph Страницы: 53

Бренд: PIAGGIO Страницы: 275

WOLVERINE R MAX 2021

Бренд: Yamaha Страницы: 190

Бренд: Yamaha Страницы: 194

WOLVERINE RMAX2 2024

Бренд: Yamaha Страницы: 196

Vstar XVS650T 2004

Бренд: Yamaha Страницы: 101

Бренд: DYNATEK Страницы: 1

Бренд: Shark Страницы: 76

Бренд: hepco & becker Страницы: 2

Бренд: Dakota Digital Страницы: 14

Бренд: Dayi Motor Страницы: 18

Бренд: Saddlemen Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды