Yamaha Majesty YP400W Скачать руководство пользователя

Страница: 59 / 102

PERIODIC MAINTENANCE AND MINOR REPAIR

6-18

5. Install the final transmission oil

drain bolt, and then tighten it to the
specified torque.

6. Add the specified amount of the

recommended final transmission
oil, and then install and tighten the
oil filler cap.

WARNING

EWA11310

●

Make sure that no foreign mate-
rial enters the final transmission
case.

●

Make sure that no oil gets on the

tire or wheel.

7. Check the final transmission case

for oil leakage. If oil is leaking,
check for the cause.

EAU20070

Coolant

The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.

EAU34192

To check the coolant level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

NOTE:

●

The coolant level must be checked
on a cold engine since the level
varies with engine temperature.

●

Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the

side can result in a false reading.

2. Pull up the right floorboard mat as

shown.

1. Final transmission oil filler cap
2. Final transmission oil drain bolt

Tightening torque:

Final transmission oil drain bolt:

20 Nm (2.0 m·kgf, 14.5 ft·lbf)

Recommended final transmission
oil:

See page 8-1.

Oil quantity:

0.25 L (0.26 US qt) (0.22 Imp.qt)

Содержание Majesty YP400W







































































































Результаты поиска

Содержание Majesty YP400W

Отзывы:

Похожие инструкции для Majesty YP400W

Бренды по названию

Популярные бренды

Yamaha Majesty YP400W, Руководство пользователя

Результаты поиска

Содержание Majesty YP400W

Отзывы:

Похожие инструкции для Majesty YP400W

Бренды по названию

Популярные бренды