Yamaha Majesty YP400W Скачать руководство пользователя

Страница: 34 / 102

INSTRUMENT AND CONTROL FUNCTIONS

3-16

With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Keep the front or rear brake applied.
5. Push the start switch.

Does the engine start?

With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear brake applied.
8. Push the start switch.

Does the engine start?

With the engine still running:
9. Move the sidestand down.

Does the engine stall?

The system is OK.

The scooter can be ridden.

This check is most reliable if performed with
a warmed-up engine.

The sidestand switch may be defective.

The scooter should not be ridden

until

checked by a Yamaha dealer.

The brake switch may be defective.

The scooter should not be ridden

until

checked by a Yamaha dealer.

The sidestand switch may be defective.

The scooter should not be ridden

until

checked by a Yamaha dealer.

YES

NOTE:

Содержание Majesty YP400W







































































































Результаты поиска

Содержание Majesty YP400W

Отзывы:

Похожие инструкции для Majesty YP400W

Бренды по названию

Популярные бренды

Yamaha Majesty YP400W, Руководство пользователя

Результаты поиска

Содержание Majesty YP400W

Отзывы:

Похожие инструкции для Majesty YP400W

Бренды по названию

Популярные бренды