Troubleshooting
Symptom
Cause
Solution
The power does not
turn on.
The power cord is disconnected.
Connect the power cord.
The protection function of the device has been
activated.
Turn off the power switch and make sure the
connection is secure. Wait several minutes, and then
turn on the power again.
No sound is heard.
The sound is lowered too much with the
[VOLUME] knob.
Turn the [VOLUME] knob to the right.
No audio signal is being input.
Make sure that this device is properly connected to
external devices.
Make sure that the external device outputs audio
signal.
The input is not selected.
Turn the [ST SOURCE] to select input jacks connected
to an external device.
The connected microphone is a condenser type. Use a dynamic type microphone or supply phantom
power to the condenser microphone.
The sound distorts.
The input level from microphones or external
devices is too high.
Turn the [MIC IN 1] knob/the [MIC IN 2 GAIN] trimmer
to the left to lower the volume of the microphones.
Lower the input volume from the external devices.
The EQ level is too high.
Turn the [SOURCE EQ BASS]/[SOURCE EQ TREBLE]
knob to the left to lower the EQ.
The setting does not
change even when
turning a knob.
The panel is locked. When the panel is locked,
even when turning the [ST SOURCE] knob,
[SOURCE EQ BASS] knob or [SOURCE EQ
TREBLE] knob, the setting of the device does
not change.
Set DIP switch 8 to the upward position and turn on
the power again.
The sound is small.
The device is set to low-impedance connection;
however, speakers with high-impedance input
have been connected.
Match the impedance settings of this device and the
connected speakers.
The sound drops
out and the power
indicator flashes
three times.
The device is set to high-impedance connection;
however, speakers with low-impedance input
have been connected or too many speakers are
connected.
Match the impedance setting and the input rating
setting of this device and the speakers.
When the device is set to low-impedance
connection, the total impedance of the
connected speakers is less than the impedance
setting of this device.
Match the impedance settings of this device and the
speakers.
The speaker cable is shorted.
Inspect the connection of the speaker cables.
The power indicator
continues flashing.
The internal temperature of the device is
extremely high.
Turn off the power, leave the device at a well-ventilated
place, and turn on the device several minutes later.
• Refer also to the Yamaha Pro Audio website that provides a FAQ (a list of frequently asked questions, with answers).
http://www.yamahaproaudio.com/
• If taking the above steps does not solve the problem, contact your Yamaha dealer for repair.
Specifications (MA2030/PA2030)
Output Power
(20msec burst, THD+N=1%)
3Ω/4Ω
30 W x 2 ch
70V/100V
60 W x 1 ch
Amplifier Type
(Output circuitry)
Class D
THD+N
Stereo in
à
Speaker out,
1kHz, 15W, 3Ω/4Ω
≤
0.1 %
Stereo in
à
Speaker out,
1kHz, 30W, 70V/100V
≤
0.2 %
Frequency Response
Line in
à
Line out,
20 Hz–20 kHz
0 dB, -2.5 dB, +1.0 dB
Line in
à
Speaker out,
50 Hz–20kHz, 1W, 3 or 4ohms
0 dB, -3.0 dB, +1.0 dB
Line in
à
Speaker out,
90 Hz–20kHz, 1W, 70V/100V
0 dB, -3.0 dB, +1.0 dB
Crosstalk
(MA2030 only)
Stereo in to other Stereo in
≤
-70 dB
AC Power Requirement
100V/120V/230V-240V,
50Hz/60Hz
Power Consumption
(3Ω, AC100V)
1/8 max. power,
pink noise at all channel,
30 W
Idle, 3Ω, AC100V
25 W
Operating Temperature
0°C–+40°C
Storage Temperature
-20°C–+60°C
Dimensions
(W x H x D, including knob)
215 x 54 x 288 mm
(8.5 x 2.1 x 11.4 inch)
Net Weight
1.8 kg
(4.0 lbs)
Optional Accessories
Rack-mount Accessory RKH1
Digital Control Panel DCP1V4S
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right
to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options
may not be the same in every locale, please check with your Yamaha dealer.
European Models
Inrush Current based on EN 55103-1:2009
3.0A (on initial switch-on)
2.0A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Rear panel
7
8 9
0
A
B
C
D
7
9
0
E
8
MA2030
PA2030
7
AC IN connector
Connect the supplied power cord.
Caution
• When connecting the power cord, connect the power cord to the connector and then plug it into an appropriate AC power
outlet.
• Before connecting or disconnecting the power cord, make sure that the power to the device is turned off.
8
[SPEAKERS] output terminals
Barrier strip type speaker output connectors. Refer to “Connecting Speaker Cables” for the installation instructions.
9
[OUTPUT] switch
Sets the output type of amplifier: high-impedance connection ([100V], [70V]) or low-impedance connection ([4Ω
3Ω]). The setting change will be reflected after turning on again.
Front panel
MA2030 (PA2030 has only
4
and
6
)
1
2
3
4
5
6
1
[MIC IN 1] jack
Combo input jack that accepts both phone-type and XLR-type. Connect dynamic microphones mainly. Input signal
is always processed through high pass filter (120Hz, 12dB/oct.) to cut off low frequency signal and Feedback
Suppressor to suppress howling.
[MIC IN 1 SIGNAL] indicator
Lights when signal is input to the [MIC IN 1] jack.
[MIC IN 1] knob
Adjusts the volume of the microphone connected to the [MIC IN 1] jack. Turning to the right increases the volume.
2
[ST IN 1] jack
Input jack of mini-stereo type (unbalanced input).
Connect a stereo audio source such as portable audio players.
3
[ST SOURCE] indicator 1/2/3
Selecting input signal from the [ST IN 1] jack lights indicator 1, the [ST IN 2] jacks lights indicator 2, and the [ST IN 3]
jacks lights indicator 3.
[ST SOURCE] knob
Rotating this switches among the stereo input signals.
Pressing and holding this lets you adjust the volume balance of stereo inputs.
Refer to “Matching the volume levels of external devices” (Step 4).
4
[VOLUME SIGNAL] indicator
Lights when signal output to speakers exceeds a
certain level.
[VOLUME LIMIT] indicator
Lights if signal output to the speakers exceeds
the limit value, causing the limiter to activate, or if
the internal temperature of the device increases
abnormally. If the limiter activates, turn the
[VOLUME] knob to the left so the indicator light goes out. If the device internal temperature increases, leave the device
without turning on the power until the internal temperature goes down.
[VOLUME] knob
Adjusts the volume output to the speakers. Turning to the right increases the volume. Turning all the way to the left mutes
the sound.
5
[SOURCE EQ BASS] knob
Adjust the volume of the low frequency (around 125Hz) stereo signal from -10dB to +10dB. At the center position, the sound
is flat; turning to the left lowers the low frequency signal and turning to the right increases the low frequency signal. Turning to
the right 90 degrees or more from the center activates the Enhancer to further emphasize the low frequency signal.
[SOURCE EQ TREBLE] knob
Adjust the volume of the high frequency (6 kHz or more) stereo signal from -10dB to +10dB. At the center position, the sound
is flat; turning to the left lowers the high frequency signal and turning to the right increases the high frequency signal. Turning
to the right 90 degrees or more from the center activates the Enhancer to further emphasize the high frequency signal.
Note
If the sound distorts when using EQ, turn the knob to the left until the sound is not distorted or lower the volume of the
stereo source.
6
Power indicator
Turns on when the power is on.
If flashing continues for 10 seconds or more, the internal temperature of the device is extremely high. Turn off the power
once, and turn on again several minutes later.
Power switch
Turn on/off the power.
Caution
• To ensure that high-volume noise is not output from the speakers, power on the connected device first and then turn on this
device. When turning the system off, turn off this device, and then the connected devices.
• After turning the power switch off, wait for about five seconds before turning it on again. Rapidly turning the power switch on
and off in succession can cause the unit to malfunction.
Note
Do not turn off the power switch three seconds or less after executing an operation. If you do, some setting information may
not be saved.
0
[SETUP] DIP switches
Set the following functions of the device. The setting change will be reflected after turning on again.
number
setting function
up
down
1
OUTPUT
Sets the speaker impedance if the [OUTPUT] switch is
set to [4Ω 3Ω] (low-impedance connection).
4Ω
3Ω
2
MIC 1 DUCKER
Turns on/off the Ducker of the [MIC in 1] jack.
OFF
ON
3
MIC 2 DUCKER
Turns on/off the Ducker of the [MIC in 2] jack.
OFF
ON
4
SP EQ
Sets the speaker output to appropriate frequency
characteristics for Yamaha speakers designed for
commercial installations.
OFF
ON
5
If DIP switch 4 is set to on, this optimizes for the type of
Yamaha speakers designed for commercial installations
SURFACE
CEILING
6
LEVELER
Turn on/off the Leveler.
OFF
ON
7
MIXER
In low-impedance installation of speakers, this sets the
speaker output to stereo or mono.
MONO
STEREO
8
PANEL LOCK
Several knobs on the front panel are locked. Refer to
“Panel Lock” for details.
UNLOCK
LOCK
Note
• When the device is shipped from the factory, the DIP switches are all in the up position.
• If DIP switches 2 and 3 (MIC 1 DUCKER and MIC 2 DUCKER) are set to on, when both microphones are used
simultaneously, the [MIC IN 1] jack is prioritized and the microphone input that connected to the [MIC IN 2] connector is
muted.
• The output of the [LINE OUT] jacks does not reflect the stereo/mono setting in [SETUP] DIP switch 7 (MIXER).
A
[DCP] connector
Connect one Yamaha Digital Control Panel DCP1V4S. Refer to “Option 2 Operating with Control Panel” for connection
method.
B
[LINE OUT] jacks
RCA type stereo output jack (unbalanced output). Outputs to the [LINE IN] jacks of PA2030 and line input jacks of other
external devices. Outputs a mixed signal of the selected stereo input, the [MIC IN 1] jack input and the [MIC IN 2] jack input.
C
[ST IN 2] jacks/[ST IN 3] jacks
RCA type stereo input jack (unbalanced output). Connect external devices such as CD player, etc. Select input jacks with
the [ST SOURCE] knob on the front panel.
D
[MIC IN 2] connector
Euroblock 3-pin connector for microphone audio input (balanced). Refer to “Attaching Euroblock Plugs” for Euroblock
plug installation. The input signal is always processed through a high pass filter (120Hz, 12dB/oct.) to cut off low
frequency signals as well as a Feedback Suppressor to suppress howling.
[MIC IN 2 GAIN] trimmer
Adjust the volume of microphone that is connected to the [MIC IN 2] connector. Adjust with a slotted driver of the correct size.
E
[LINE IN] jacks/connectors
RCA type and Euroblock 3-pin stereo input jacks/connectors (RCA: unbalanced; Euroblock 3-pin: balanced). Connect to
the [LINE OUT] jacks of the MA2030 or output jacks of other external devices. The signals input from the RCA type jacks
and Euroblock connector will be mixed to the output.
Controls and Connectors
Setting
Signal level for which each indicator turns on
[VOLUME SIGNAL]
Low-impedance
connections
[3Ω]
-18.2 dBu or more
[4Ω]
-17.0 dBu or more
High-impedance
connections
[70V]
-0.8 dBu or more
[100V]
2.3 dBu or more
PLEASE READ CAREFULLY BEFORE
PROCEEDING
Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid
the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These
precautions include, but are not limited to, the following:
Power supply/power cord
• Do not place the power cord near heat sources such as heaters
or radiators, and do not excessively bend or otherwise damage
the cord, place heavy objects on it, or place it in a position
where anyone could walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the device. The
required voltage is printed on the name plate of the device.
• Use only the supplied power cord. If you intend to use the
device in an area other than in the one you purchased, the
included power cord may not be compatible. Please check
with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or
dust which may have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective
grounding connection. Improper grounding can result in
electrical shock, damage to the device(s), or even fire.
Do not open
• This device contains no user-serviceable parts. Do not
open the device or attempt to disassemble the internal
parts or modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in damp
or wet conditions, or place on it any containers (such as vases,
bottles or glasses) containing liquids which might spill into any
openings. If any liquid such as water seeps into the device,
turn off the power immediately and unplug the power cord from
the AC outlet. Then have the device inspected by qualified
Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit. A
burning item may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately turn off
the power switch and disconnect the electric plug from the outlet.
Then have the device inspected by Yamaha service personnel.
– The power cord or plug becomes frayed or damaged.
– It emits unusual smells or smoke.
– Some object has been dropped into the instrument.
– There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off
the power switch, disconnect the electric plug from the outlet, and
have the device inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the
possibility of physical injury to you or others, or damage to
the device or other property. These precautions include, but
are not limited to, the following:
Power supply/power cord
• When removing the electric plug from the device or an outlet,
always hold the plug itself and not the cord. Pulling by the cord
can damage it.
• Remove the electric plug from the outlet when the device is not to
be used for extended periods of time, or during electrical storms.
Location
• Do not place the device in an unstable position where it might
accidentally fall over.
• Do not block the vents. This device has ventilation holes at the top/
bottom/sides to prevent the internal temperature from becoming
too high. In particular, do not place the device on its side or
upside down. Inadequate ventilation can result in overheating,
possibly causing damage to the device(s), or even fire.
• When attempting to dissipate heat on the device, when
installing it:
– Do not cover it with any cloth.
– Do not install it on a carpet or rug.
– Make sure the top surface faces up; do not install on its
sides or upside down.
– Do not use the device in a confined, poorly-ventilated
location.
Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), or even fire.
Make sure that there is adequate space around the device: at
least 10 cm above, 1 cm below the bottom surface, 10 cm at
the sides and 10 cm behind.
• Do not place the device in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you
are using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and disconnect
the plug from the outlet. Even when the power switch is turned
off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time,
make sure to unplug the power cord from the wall AC outlet.
• If the device is mounted in an EIA standard rack, carefully
read the section “Precautions for rack mounting”. Inadequate
ventilation can result in overheating, possibly causing damage
to the device(s), malfunction, or even fire.
Connections
• Before connecting the device to other devices, turn off the
power for all devices. Before turning the power on or off for all
devices, set all volume levels to minimum.
• Use only speaker cables for connecting speakers to the
speaker jacks. Use of other types of cables may result in fire.
Maintenance
• Remove the power plug from the AC outlet when cleaning the
device.
Handling caution
• When the surface of the device heats up, do not touch it until
the panel temperature goes down. Touching the surface with
its high temperature may cause burns.
• Avoid inserting or dropping foreign objects (paper, plastic,
metal, etc.) into any gaps or openings on the device (vents,
etc.) If this happens, turn off the power immediately and
unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects
on it, and avoid use excessive force on the buttons, switches
or connectors.
• Do not use the device for a long period of time at a high or
uncomfortable volume level, since this can cause permanent
hearing loss. If you experience any hearing loss or ringing in
the ears, consult a physician.
• Do not operate the device if the sound is distorting. Prolonged
use in this condition could cause overheating and result in fire.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the device, or data that is lost
or destroyed.
NOTICE
To avoid the possibility of malfunction/ damage to the product, or
damage to other property, follow the notices below.
Handling and maintenance
• Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices. Otherwise,
the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a heater,
or in a car during the day), in order to prevent the possibility
of panel disfiguration, unstable operation, or damage to the
internal components.
• Do not place vinyl, plastic or rubber objects on/under the
device, since this might discolor the panel of the device or the
objects placed on/under the device.
• Keep input cables of microphone, etc., devices that contain
sensitive circuits, and the power cord at a distance from
speaker cables and fasten the speaker cables in place.
Since a large amount of current can flow in a speaker cable,
a magnetic field will be generated and may produce radio
interference and acoustic noise.
• When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemical-
impregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic
changes in ambient temperature–when the device is moved
from one location to another, or air conditioning is turned
on or off, for example. Using the device while condensation
is present can cause damage. If there is reason to believe
that condensation might have occurred, leave the device
for several hours without turning on the power until the
condensation has completely dried out.
• Avoid setting all equalizer controls and faders to their
maximum. Depending on the condition of the connected
devices, doing so may cause feedback and may damage the
speakers.
• Do not use this device for any purpose other than driving
loudspeakers.
• When turning on the AC power in your audio system, always
turn on the device LAST, to avoid speaker damage. When
turning the power off, the device should be turned off FIRST for
the same reason.
• If you put the device on a table or a rack, do not remove the
rubber feet from the device.
• Always turn the power off when the device is not in use.
Connectors
XLR-type connectors are wired as follows (IEC60268 standard):
pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Precautions for rack mounting
This unit is rated for operation at ambient temperatures ranging
from 0 to 40 degrees Celsius. If the device is mounted with
other devices in an EIA standard equipment rack, internal
temperatures can exceed the specified upper limit, resulting in
impaired performance or failure. If the device is mounted in a
rack, always observe the following requirements to avoid heat
buildup:
• If the device is mounted in a rack with other devices that
generate a significant amount of heat, such as a power
amplifier, leave more than 1U of space between the device
and other devices (both above and below). Also, make sure to
either leave any open spaces uncovered or install appropriate
ventilating panels to minimize the possibility of heat buildup.
• To ensure sufficient airflow, leave the rear of the rack open and
position it at least 10 centimeters from walls or other surfaces.
If you’ve installed a fan kit, there may be cases in which
closing the rear of the rack will produce a greater cooling
effect. Refer to the rack and fan unit manual for details.
PRECAUTIONS
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
HEAD OFFICE
Yamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: 714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
MALTA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
Tel: +971-4-881-5868
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağ?ms?z Böl. No:3, 34398 Şişli İstanbul
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
Tel: +971-4-881-5868
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietna m Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
PA36
Yamaha Pro Audio global web site:
http://www.yamahaproaudio.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
C.S.G., PA Development Division
© 2014 Yamaha Corporation
Published 05/2014 405KSHD-A0
Printed in China
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/or
another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use
of this product in a residential environment will not result
in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in
the users manual, may cause interference harmful to the
operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not occur
in all installations. If this product is found to be the source of
interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Corporation of
America, Electronic Service Division, 6600 Orangethorpe
Ave, Buena Park, CA90620
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
(class B)
The model number, serial number, power requirements, etc.,
may be found on or near the name plate, which is at the
bottom of the unit.
You should note this serial number in the space provided
below and retain this manual as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
(bottom_en_01)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in
accordance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be
connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or colored GREEN or
GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
(3 wires)
In Finland: Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan.
In Norway: Apparatet må tilkoples jordet stikkontakt.
In Sweden: Apparaten skall anslutas till jordat uttag.
(class I hokuo)
CAN ICES-3 (B)/NMB-3(B)
This applies only to products distributed by Yamaha Canada
Music Ltd.
(can_b_01)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
(fcc_sengen-C)
이 기기는 가정용(B급) 전자파적합기기로서 주로
가정에서 사용하는 것을 목적으로 하며, 모든
지역에서 사용할 수 있습니다.
(class b korea)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The above warning is located on the top of the unit.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection
points, in accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from inappropriate waste
handling.
For more information about collection and recycling of old products, please contact your local municipality,
your waste disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of disposal.
(weee_eu_en_01)
