Yamaha LZ250 Скачать руководство пользователя

Страница: 48 / 87

Operation

on page 39. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

●

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this

could break the handle.

EMU28005

Procedure for tilting up

Power trim and tilt models / power tilt models
1.

Place the remote control lever / the gear
shift lever in neutral.

Disconnect the fuel line from the out-
board motor or close the fuel cock.

Press the power trim and tilt switch /
power tilt switch “

” (up) until the out-

board motor has tilted up completely.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

ZMU03196

ZMU04588

ZMU04602

ZMU01954

✩✱✣✬✤✧✲✣ ✧✦

2019 Yamaha Motor Corporation, U.S.A.

Содержание LZ250
























































































Результаты поиска

Содержание LZ250

Отзывы:

Похожие инструкции для LZ250

Бренды по названию

Популярные бренды

Yamaha LZ250, Руководство пользователя

Результаты поиска

Содержание LZ250

Отзывы:

Похожие инструкции для LZ250

Бренды по названию

Популярные бренды