Yamaha LZ250 Скачать руководство пользователя

Страница: 23 / 87

Basic components

EMU26340

Tilt support lever for power trim and
tilt or hydro tilt model

To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
clamp bracket.

EMU26382

Top cowling lock lever (pull up type)

To remove the engine top cowling, pull up
the lock lever(s) and lift off the cowling.
When installing the cowling, check to be sure
it fits properly in the rubber seal. Then lock
the cowling by moving the lever(s) down-
ward.

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 51.

1. Trim tab
2. Bolt
3. Cap

ZMU01863

ZMU01864

1. Top cowling lock lever(s)

ZMU04933

ZMU04934

✩✱✣✬✤✧✲✣ ✤✫

2019 Yamaha Motor Corporation, U.S.A.

Содержание LZ250
























































































Результаты поиска

Содержание LZ250

Отзывы:

Похожие инструкции для LZ250

Бренды по названию

Популярные бренды

Yamaha LZ250, Руководство пользователя

Результаты поиска

Содержание LZ250

Отзывы:

Похожие инструкции для LZ250

Бренды по названию

Популярные бренды