Yamaha HTR-62300, Руководство пользователя

Страница: 19 / 85

17
En
Optimizing the speaker setting for your listening room (YPAO)
English
INTR
ODUCTION
AD
DITIONAL
INFORMA
T
ION
APPENDIX
PRE
P
ARA
T
ION
BA
S
IC
OPERA
T
ION
AD
V
ANCED
OPERA
T
ION
Notes
• During the automatic setup procedure, do not perform any
operation on this unit.
• We recommend that you get out of the room while this unit is in the
auto setup procedure. It takes approximately 3 minutes for this unit
to complete the auto setup procedure.
6
When all measurements are completed
successfully, “FINISH” appears on the front
panel display.
The result of the automatic setup for each speaker
appears in order on the front panel display.
y
• To display the result of the automatic setup again, press
l k
/
n
repeatedly.
Notes
• If you select “RELOAD” in step 4, no test tones are output.
• If an error occurs during the “AUTO:CHECK” procedure, the
setup procedure is canceled and an error screen appears. For
details, see “If an error screen appears” on page 17.
• When this unit detects potential problems during the “AUTO
SETUP” procedure, “WARNING” and the warning messages
appear after this unit displays the result of the automatic setup. For
details, refer to the “AUTO SETUP” section in “Troubleshooting”
on page 43.
• The distance measurement result may be longer than the actual
distance depending on the characteristics of your subwoofer.
7
Press
l l
/
h
to select “SET” or “CANCEL.”
8
Press
l
ENTER to confirm your selection.
“AUTO SETUP” appears on the front panel display.
9
Press
k
MENU to exit from “SET MENU.”
10
Disconnect the optimizer microphone from
this unit.
The optimizer microphone is sensitive to heat. Keep it
away from direct sunlight and do not place it on top
of this unit.
y
•
If you change speakers, speaker positions, or the layout of your
listening environment, run “AUTO SETUP” again to recalibrate
your system.
•
When you want to check the result of the automatic setup in detail
or manually adjust the parameters, use “MANUAL SETUP” (see
page 31).
■
If an error screen appears
If this unit detects the potential problems, an error
message appears on the front panel display during the
automatic setup.
For details about each error message, see the “AUTO
SETUP” section in “Troubleshooting” on page 43.
After a few seconds later, the following choices appear.
Press
l l
/
h
to select “RETRY” or “EXIT” and then
press
l
ENTER .
■
If “WARNING” appears
When this unit detects potential problems during the
automatic setup procedure, “WARNING” appears on the
front panel display after result of each speaker. Check the
warning messages to correct your speaker settings.
Note
•
Warnings differ from errors in that warnings do not cancel the automatic
setup procedure.
Press
l
n
to display the detailed information
about the warning.
The detailed information about the warning is displayed
and the indicators of inapplicable speakers blink on the
front panel display.
y
• For details about each warning message, see the “AUTO SETUP” section
in “Troubleshooting” on page 43.
Choice Function
SET
* Confirms the “AUTO SETUP” results.
CANCEL
Cancels the “AUTO SETUP” results.
FL: 3.3m +2
The distance between the speaker
and the listening position
The result of the
adjustment of the
volume level
Speaker
FL/FR: Front left/right
C: Center
SL/SR: Surround left/right
SW: Subwoofer
Choice Function
RETRY
* Starts the “AUTO SETUP” again.
EXIT
Exits from the “AUTO SETUP” procedure.
PHASE REVERSED
LFE
L C R
SL SR
Flashes