Yamaha FZS10Z Скачать руководство пользователя страница 34

Страница: 34 / 110

INSTRUMENT AND CONTROL FUNCTIONS

4-16

TIP

Make sure that the seats are properly
secured before riding.

EAU14462

Storage compartment

The storage compartment is located
under the passenger seat. (See page
4-15.)

WARNING

EWA10961

●

Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of FZS10Z 190 kg (419 lb)
FZS10ZC 189 kg (417 lb) for the
vehicle.

When storing the Owner’s Manual or
other documents in the storage com-
partment, be sure to wrap them in a
plastic bag so that they will not get wet.

When washing the vehicle, be careful
not to let any water enter the storage
compartment.

1. Storage compartment

U1CA10E0.book Page 16 Tuesday, November 24, 2009 1:41 PM

Содержание FZS10Z















































































































Результаты поиска

Содержание FZS10Z

Отзывы:

Похожие инструкции для FZS10Z

Бренды по названию

Популярные бренды

Yamaha FZS10Z, Руководство пользователя

Результаты поиска

Содержание FZS10Z

Отзывы:

Похожие инструкции для FZS10Z

Бренды по названию

Популярные бренды