background image

Operation

52

If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to in-
stall the drain screw after draining the water
separator.

EJU32452

Bilge 

Check the bilge for moisture and fuel residue.

NOTICE:

 Excessive water in the engine

compartment can splash into the engine,
which can result in severe damage.

 [ECJ00341]

This watercraft is equipped with a convention-
al jet vacuum bilge draining system and an
electric bilge draining system. The electric
bilge draining system is operated when the
engine is running. When excess water reach-
es the water inlet of the electric bilge pump,
the water is discharged from the electric bilge
pilot outlet at the stern.

A small quantity of water will remain in the
bilge and should be drained manually. To
drain any residual water, beach the watercraft
and perform the following procedure.
To drain water from the bilge:
(1) Remove the stern drain plugs.
(2) Raise the bow of the watercraft until the

water drains.

(3) After the water has drained, wipe the

bilge with dry rags to make sure that it is
thoroughly dry.

(4) Install the stern drain plugs. 

NOTICE:

Before installing the stern drain plugs,
clean the drain plug threads to remove
any foreign materials, such as dirt or
sand. Otherwise, the stern drain plugs
could be damaged, allowing water to
enter the engine compartment. Make
sure that the stern drain plugs are
tightened securely before launching
the watercraft. Otherwise, water may
flood the engine compartment and
cause the watercraft to submerge.

[ECJ00361]

EJU32472

Stern drain plugs 

Check the stern drain plugs for proper instal-
lation.

EJU32482

Battery 

Check the battery electrolyte level and check
that the battery has sufficient power to start
the engine easily. 

WARNING! Never operate

the watercraft if the battery does not have
sufficient power to start the engine or if it
shows any other signs of decreased pow-
er. Loss of battery power may leave you
stranded.

 [EWJ01240]

1

Electric bilge pilot outlet

1

1

Stern drain plugs

1

UF2R10E0.book  Page 52  Friday, October 31, 2008  9:14 AM

Содержание FZR 1800









































































































Отзывы: